Sony KP-43T70C Manufacturer code numbers cable box, To operate the cable box, Picture turns off

Operating a Cable Box

Setting the Manufacturer's Code

You can program the supplied remote control to operate a cable box.

Press CODE SET, SAT/CABLE (FUNCTION)*, and the 0-9 buttons to enter the manufacturer’s code number (see the following chart), then press ENTER.

For example, to operate a Pioneer cable box:

CODE SET	FUNCTION		ENTER
	SAT/CABLE	1
	2		4

Manufacturer code numbers (cable box)

Manufacturer	Code
Hamlin/Regal	222, 223, 224, 225, 226
Jerrold/G.I	201, 202, 203, 204, 205,
	222, 206, 207, 208, 218
Oak	227, 228, 229
Panasonic	219, 220, 221
Pioneer	214, 215
Scientific Atlanta	209, 210, 211
Tocom	216, 217
Zenith	212, 213

To operate the cable box

1Press SAT/CABLE (POWER)* [Green Button] to turn on/off the cable box.

2Press SAT/CABLE (FUNCTION)*.

3For other operations, refer to the operating instructions that come with the equipment.

*The SAT/CABLE (POWER) and SAT/CABLE (FUNCTION) buttons cannot operate a satellite receiver (SAT) in Argentine and Chile even if it is connected to the projection TV.

If the remote control doesn’t work

•Try repeating the set up procedures using the other codes listed for your equipment.

To operate the projection TV

Press TV (FUNCTION). Then use the projection TV control buttons to control the projection TV.

Tips z

•If more than one code number is listed, try entering them one by one until you come to the correct code for your equipment.

•If you enter a new code number, the code number you previously entered at that setting is erased.

•In some rare cases, you may not be able to operate your equipment with the supplied remote control. In this case, use the equipment’s own remote control unit.

•Whenever you remove the batteries — to replace them, for example — if too much time is taken, the code numbers may revert to the factory setting and must be reset.

3 2

Troubleshooting

If, after reading the following instructions, you have additional questions related to the use of your Sony projection TV, please contact your nearest Sony Authorized Service Center.

The picture turns off and the	• The projection TV is equipped with a self-diagnosis function. If there is a problem with your projection TV, the TIMER/STAND BY indicator on the front
TIMER/STAND BY indicator on the	panel will flash repeatedly. Counting the number of flashes helps you inform qualified Sony Authorized Service Center of the projection TV’s condition.
front panel flashes (self-diagnosis	• Press POWER on the projection TV to turn it off, then inform qualified Sony Authorized Service Center of the number of flashes.
function)
No picture (screen not lit), no	• Make sure the power cord is plugged in.
sound	• Operate with the buttons on both the projection TV and the remote control.
	• Check to see if the TV/VIDEO setting is correct: when watching TV, set to TV, and when watching video tapes, set to VIDEO 1, 2, or 3.
	• Try another channel. It could be station trouble.
	• Perform AUTO SET UP again using the SET UP button to return to the factory preset condition. (see “To perform AUTO SET UP again” on page 13)

Remote control does not operate

•Batteries could be weak. Replace the batteries.

•Press TV (FUNCTION) when operating your projection TV.

•Make sure the projection TV’s power cord is connected securely to the wall outlet.

•Locate the projection TV at least 3-4 feet away from fluorescent lights.

•Check the polarity of the batteries.

Dark, poor or no picture (screen lit), good sound

•Adjust “Contraste” in the Video menu. (see “Ajuste de imagen” on page 20)

•Adjust “Brillo” in the Video menu. (see “Ajuste de imagen” on page 20)

•Check antenna/cable connections.

•Perform AUTO SET UP again using the SET UP button to return to the factory preset condition. (see “To perform AUTO SET UP again” on page 13)

•Adjust the convergence again using the FLASH FOCUS button. (see “Adjusting the Convergence Automatically (FLASH FOCUS)” on page 13)

Good picture, no sound	• Press MUTING so that “Suprimir el sonido” disappears from the screen. (see “MUTING” on page 14)
	• Check the MTS/SAP setting in the Audio menu. (see “MTS/SAP” on page 21)
	• Make sure “Parlantes” is set to “Sí” in the Audio menu. (see “Parlantes” on page 22)
	• Perform AUTO SET UP again using the SET UP button to return to the factory preset condition. (see “To perform AUTO SET UP again” on page 13)
	• Set the appropriate TV color system in the Ajustes menu. (see “Sistema de color” on page 29)
	(continued)
	3 3
	– 23 –