Sony PCM-R500 Disabling Button Operations Key Protect Function, PCM-R700Only, 28EN, Pin No, MODE1

Additional Information

Remote Control Function Using a Parallel Remote Connector

You can operate the deck with a parallel remote control that uses a switch box connected to the REMOTE 1 connector on the rear panel.

Using the REMOTE 1 connector

When operating the deck with a parallel remote control, set the REMOTE switch on the front panel to

WIRED.

The pin numbers and pin assignments for the REMOTE 1 connector on the rear panel are as follows:

				DIN connector (8 pin)
				7		8		6
				3				1
				5				4		Case
						2			y
	Pin No				MODE1				MODE2
					(playback)				(recording)
Inputs	1				H-level constant				L-level constant
	2				H-STOP/L-PLAY				L-STOP
	3				L-STOP				L-START ID
									WRITE
	4				L-PLAY				L-PLAY
	5				L-REW				L-PAUSE
	6				L-FF				L-REC
Status	7				H-STOP				H-REC-PAUSE
output	8				H-PLAY				H-REC
Case					GND				GND
Command inputs				H: OPEN (off impedance: 30 kilohms or
					more)
				L: GND short (on impedance: 100 ohms
					or less)
Status output				H: approx 2V (I=15mA)
				L: OPEN (High impedance)
Connection diagram (MODE 1)
1	2		3	4		5	6	7	8	Case
OPEN										GND
		Command input						Status output
		switch						display (LED)

28EN

Notes

•When using MODE 2, use pin number 1 for GND.

•By keeping the input to pin number 1 constant at either H- level or L-level determines whether pin numbers 2 to 8 are in MODE 1 (playback) or MODE 2 (recording).

•In MODE 1, pin number 2 may be used for fader-start function.

•For pin numbers 2 to 6 pin, input to smaller numbers take priority.

•Anti-chattering measures should be taken for the command input switches.

•Status output (pin numbers 7 and 8) is specially provided for driving a single LED. If more current is needed, use an additional drive circuit or electric power supply.

•Do not switch input to pin number 1 (MODE 1 and MODE 2) while the deck is playing or recording. This may result in mis-operation of the deck.

Disabling Button Operations

(Key Protect Function)

(PCM-R700 Only)

You can disable certain button operations so that the buttons do not work during, for instance, recording.

KEY PROTECT

INPUT

ANALOG

DIGITAL

MODE

ANALOG INPUT

POWER

UNBALANCE

BALANCE

COUNTER RESET

¯ ON

¿ OFF

REC MODE

STANDARD

LONG

REMOTE

MARGIN RESET

WIRED OFF WIRELESS

48k

44.1k

OFF

SBM

ON

KEY PROTECT

SHUTTLE

DATA

OFF

ON

AMS

PREVIOUS

NEXT

REW

FF

REC MUTE

MENU

REC LEVEL

=

+

0

)

R

r

CH-1(L)

•

PHONE LEVEL

•

•

START ID

INPUT

OPEN/CLOSE

STOP

PLAY

PAUSE

REC

•

AUTO

REHEARSAL

WRITE

ERASE

MONITOR

REPEAT

LOCATE

SET

•

•

•

6

p

(

P

r

0

10

MIN•

MAX

SKIP ID

CH-2(R)

•

PHONES

RENUMBER REHEARSAL

WRITE

ERASE

FADER

SKIP PLAY

MARK

•

•

0•

10

All of these buttons and dials are disabled.

Set KEY PROTECT to ON.

3-859-278-11(1)