Settings Detailed and Displays Menu 5 Chapter
2)When an Anton Bauer battery system or a
INT: When one of the above batteries is installed, the remaining power is shown as a percentage value (%) when there is a change in the value or when the power is low.
AUTO: The remaining power is shown as a percentage value (%) when one of the above batteries is installed. Otherwise the voltage (VOLT) is displayed continuously.
VOLT: The voltage (VOLT) is displayed continuously.
VF DISP 2 page
Item | Description |
DISP 5600K | Displays “5600K”. |
|
|
DISP FILTER | Displays types of the ND filter. |
|
|
DISP WHITE | Displays selected white balance |
| memory. |
|
|
DISP GAIN | Displays gain value. |
|
|
DISP SHUTTER | Displays shutter speed and ECS |
| mode. |
|
|
DISP AUDIO | Displays audio level. |
|
|
DISP DISC | Displays remaining disc capacity. |
|
|
DISP IRIS | Lens iris setting indication |
|
|
DISP LOW LIGHT | “LOW LIGHT” indication when the |
| average video level is below a |
| certain threshold. |
|
|
DISP INTERVAL | “INTERVAL TIME” indication |
| during interval recording. |
|
|
3 Turn the MENU knob to select the desired setting (ON, OFF, or value), and press the MENU knob.
4 Repeat steps 2 and 3 until you have set all of the desired items.
Change Confirmation/Adjustment Progress Messages
The messages indicating setting changes, progress and consequence of adjustments, and the situations indicated by these messages are as follows.
Setting change confirmation/adjustment progress messages
Situation | Message to appear |
The filter selection has been | FILTER: n |
changed | (where n = 1, 2, 3, 4) |
|
|
The gain setting has been | GAIN: n |
changed | (where n = |
| 6dB, 9dB,12dB, 18dB, 24dB, |
| 30dB, 36dB, 42dB, 48dB) |
|
|
The setting of the WHITE | WHITE: n |
BAL switch has been | (where n = A CH, B CH, |
changed | PRESET) or ATW: RUN |
|
|
Situation | Message to appear |
The OUTPUT/DCC switches | DCC: ON (or OFF) |
has been set to DCC ON or |
|
OFF |
|
|
|
The shutter speed and mode | SHUTTER: 1/100 (or 1/125, |
setting has been changed 1) | 1/250, 1/500, 1/1000, 1/2000, |
| ECS, SLS) |
The black or white balance | E.g. WHITE: OK |
has been adjusted |
|
|
|
1)The corresponding message is also displayed for about 3 seconds when the SHUTTER switch is set to ON.
Setting the Marker Display
You can switch the display of the center and safety zone markers on or off and select whether the area indicated by the safety zone marker is 80%, 90%, 92.5%, or 95% of the screen area.
(How to select an item in the menu screen: Turn the MENU knob to move the b mark to the desired item.)
1 Display the MARKER page of the USER (or OPERATION) menu, and press the MENU knob.
For details on menu operations, see “Basic Menu Operations” on page 132.
2 Select the desired setting item, and press the MENU knob.
You can set the following items on the MARKER page.
Item | Description |
MARKER | If you want no markers to be |
| displayed, set to OFF. |
|
|
CENTER | To display the center marker, set |
| to ON. |
|
|
SAFETY ZONE | To display the safety zone, set to |
| ON. |
|
|
SAFETY AREA | Selects the safety zone area. |
|
|
ASPECT | To display the aspect marker, set |
| to ON. |
|
|
ASPECT SELECT | Selects the type of the aspect |
| marker. (14:9/13:9/4:3) |
|
|
3 Turn the MENU knob to select the desired setting, and press the MENU knob.
4 Repeat steps 2 and 3 until you have set all of the desired items.
138 Setting the Status Display on the Viewfinder Screen and the LCD Monitor