Setup

The principal setup operations before operating this unit are carried out using setup menus.

This section explains how to set the date and time and how to adjust the brightness of the LCD panel.

See Chapter 6 “Menus” (page 81) for more information about menu operations and menu items.

Setting the Date and Time

When using this unit for the first time, you should set the date and time as follows.

Note

Before starting, press the DISPLAY button to set the monitor video section to its largest size. Or connect an external video monitor to this unit and superimpose menus (see page 37) on the monitor screen.

 

 

 

 

 

 

 

1,4

 

 

3

2,3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EJECT

 

 

0

 

0

 

TCG

F1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-12

 

-12

 

EXT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F2

 

 

 

 

 

 

 

 

 

 

-20

 

-20

 

TC MODE

 

 

 

 

 

 

 

 

ACCESS

 

-30

 

-30

 

PRESET

 

 

 

 

 

 

 

 

 

 

-40

 

-40

 

RUN MODE

F3

 

 

 

 

 

 

 

 

 

 

-60

 

-60

 

 

 

 

 

 

 

 

 

 

1

2

3

4

 

REC RUN

 

 

 

 

 

 

 

 

VAR

NETWORK

 

4CH 16 BIT

3 + 4

T C / V I T C

 

 

 

 

MENU

 

MARK1

 

 

F4

CHAPTER

 

 

 

 

 

 

MPEG HD

SP

1080 60I

 

V I T C

 

 

 

 

 

 

 

LOCAL

 

 

VITC

COOO1

REM:077M

DF/NDF

 

 

 

 

 

 

 

 

 

REMOTE

00:00.00:00

NDF

F5

EXPAND

SUB

THUMB

SET

RESET

IN

OUT

 

LEVEL

P2

 

 

CLIP

NAIL

 

 

JOG

 

 

 

 

 

 

 

PAGE DISPLAY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLIP

ESSENCE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

MARK

 

 

MARK2

 

 

PHONES

 

CH 1

 

CH 2

CH 3

CH 4

 

KEY INHI

PREV

PLAY

NEXT

STOP

REC

SHUTTLE

 

 

VARIABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PB

SHIFT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOP

F REV

F FWD END

STANDBY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 3

 

3

1 Press the MENU button.

The system menu appears on the monitor screen (see page 83).

2 Select DATE/TIME PRESET using the M/MARK1 button or m/MARK2 button, then press the ,/OUT button.

The DATE/TIME PRESET screen appears on the monitor.

DATE/TIME PRESET

YEAR

2006

MONTH

04

DAY

08

TIME

10:09:17

TIME ZONE

UTC_00:00

INC/DEC

: JOG

DIAL

SHIFT

: ( )(

)KEY

DATE

SAVE

: SET

KEY

TO

MENU

: MENU

KEY

This screen allows you to set the following items. YEAR: Calendar year

MONTH: Month

DAY: Day

TIME: Time

TIME ZONE: Time zone (difference from UTC)

3 Set the date, time and time zone.

You can change the setting of the flashing digits.

To change the flashing digits

Use the arrow buttons (</IN, ,/OUT).

To increase or decrease the values of the flashing digits

Use the arrow buttons (M/MARK1, m/MARK2) or jog dial.

To return the settings to the initial values

Press the RESET button.

4 When you have made the necessary settings, press the SET button.

The message “NOW SAVING...” appears, the settings are saved, and the menu closes.

To clear the menu from the screen without saving settings

Press the MENU button twice in succession.

Adjusting the Brightness of the LCD Panel

Proceed as follows to adjust the brightness of the LCD panel.

Note

Before starting, press the DISPLAY button to set the monitor video section to its largest size. Or connect an external video monitor to this unit and superimpose menus (see page 37) on the monitor screen.

Preparations 2 Chapter

Setup 31