Manuals / Brands / Home Audio / Stereo Receiver / Sony / Home Audio / Stereo Receiver

Sony STRDG910 6:Selecting the speaker system, 7:Calibrating the appropriate settings automatically, (AUTO CALIBRATION), To turn off the speaker output

1 96

Download 96 pages, 3.58 Mb

6:Selecting the speaker system

You can select the front speakers you want to drive.

Be sure to use the buttons on the receiver for this operation.

SPEAKERS (OFF/A/B/A+B)

?/1

								MASTER VOLUME
			MULTI CHANNEL DECODING
TONE MODE	TUNING MODE						DISPLAY	INPUT MODE
TONE	TUNING						INPUT SELECTOR
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
	MEMORY/		SUR BACK
	ENTER	DIMMER	SLEEP DECODING	2CH	A.F.D.	MOVIE	MUSIC	AUTO CAL	DIRECT
VIDEO 3 IN/PORTABLE AV IN
PHONES
VIDEO	L AUDIO R

Press SPEAKERS (OFF/A/B/A+B) repeatedly to select the front speaker system you want to drive.

To select	Light up
The speakers connected to the	SP A
SPEAKERS FRONT A terminals

The speakers connected to the	SP B
SPEAKERS FRONT B terminals

The speakers connected to both the	SP A and
SPEAKERS FRONT A and B	SP B
terminals (parallel connection)

To turn off the speaker output

Press SPEAKERS (OFF/A/B/A+B) repeatedly until the “SP A” and “SP B” indicators on the display do not light up.

Note

You cannot switch the front speaker system by pressing SPEAKERS (OFF/A/B/A+B) when the headphones are connected.

7:Calibrating the appropriate settings automatically

(AUTO CALIBRATION)

This receiver is equipped with DCAC (Digital Cinema Auto Calibration) Technology which allows you to perform automatic calibration as follows:

•Check the connection between each speaker and the receiver.

•Adjust the speaker level.

•Measure the distance of each speaker to your listening position.

•Measure the speaker polarity.

•Measure the speaker size.

•Measure the frequency characteristics.*

*• DTS 96/24 signals are always played back as 48 kHz when you correct signals.

•The measurement result is not utilized for signals with a sampling frequency of more than 96 kHz.

The DCAC is designed to obtain proper sound balance in your room. However, you can adjust the speaker levels and balance manually according to your preference. For details, see “8: Adjusting the speaker levels and balance (TEST TONE)” (page 39).

33GB

Started Getting

Contents

Page About This Manual Table of Contents Description and location of parts Page About the indicators on the display Page Rear panel Remote commander RM-AAP017 Page Page Page Page 1: Installing speakers 2: Connecting speakers 3a: Connecting the audio components Page Connecting components with analog audio jacks 3b: Connecting the video components Connecting components with HDMI jacks HDMI features If you connect a Blu-raydisc player Notes on HDMI connections Connecting a TV Page Connecting a DVD player/DVD recorder Connecting a DVD player Connecting a DVD recorder Connecting a satellite tuner/ set-topbox Page Function for conversion of video signals In the video input/output conversion table of the receiver Notes on converting video signals 4: Connecting the antennas 5:Preparing the receiver and the remote Performing initial setup operations Inserting batteries into the remote 6:Selecting the speaker system 7:Calibrating the appropriate settings automatically Before you perform Auto Calibration On setting up the active sub woofer Performing Auto Calibration To cancel Auto Calibration When error codes appear When you select “WARN CHK” When you select “PHASE” A. CAL menu parameters 8:Adjusting the speaker levels and balance Selecting a component To mute the sound To avoid damaging your speakers Listening/Watching a component Watching a DVD Navigating through menus Overview of the menus Page Page Page Adjusting the level Adjusting the equalizer Settings for the surround sound Using the surround back decoding mode Types of the surround back decoding functions Settings for the tuner Settings for the audio Settings for the video Settings for the system Page Page Page Enjoying Dolby Digital and DTS surround sound Types of A.F.D. mode If you connect a sub woofer Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Using only the front speakers Listening to the sound without any adjustment Listening to FM/AM radio Using the controls on the receiver In case of poor FM stereo reception Direct tuning If you cannot tune in a station Presetting radio stations Tuning to preset stations Naming preset stations To create an index name Using the Radio Data System (RDS) Receiving RDS broadcasts Displaying RDS information Description of program types Switching between digital and analog audio Listening to digital sound from other inputs Assignable inputs for digital audio input Enjoying the DIGITAL MEDIA PORT (DMPORT) Connecting the DIGITAL MEDIA PORT adapter To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Listening to a connected component through DMPORT connection Watching a connected component through DMPORT connection Naming inputs Changing the display Using the Sleep Timer Recording using the receiver Programming the remote If programming is unsuccessful, check the following: To clear the memory of the remote To program the remote to control a TV To cancel programming To activate the input after programming To control a CD player To control a DAT deck To control an MD deck To control a tape deck To control an LD player To control a DVD player To control a DVD recorder To control a TV To control a satellite tuner To control a cable box Glossary Page Precautions Troubleshooting Page Video Tuner Remote commander Error messages Specifications Page Page Index