2)Reference power output for front, center, surround and surround back speakers. Depending on the sound field settings and the source, there may be no sound output.
3)Measured under the following conditions: 220 V AC, 60 Hz
Frequency response |
|
Analog | 10 Hz – 70 kHz, |
| |
| field and equalizer |
| bypassed) |
Input |
|
Analog | Sensitivity: 500 mV/ |
| 50 kohms |
| S/N4): 96 dB |
| (A, 500 mV5)) |
Digital (Coaxial) | Impedance: 75 ohms |
| S/N: 100 dB |
| (A, 20 kHz LPF) |
Digital (Optical) | S/N: 100 dB |
| (A, 20 kHz LPF) |
Output (Analog) |
|
AUDIO OUT | Voltage: 500 mV/ |
| 10 kohms |
SUB WOOFER | Voltage: 2 V/1 kohm |
Equalizer |
|
Gain levels | ±10 dB, 0.5 dB step |
4)INPUT SHORT (with sound field and equalizer bypassed).
5)Weighted network, input level.
FM tuner section
Tuning range | 87.5 – 108.0 MHz |
Antenna | FM wire antenna |
Antenna terminals | 75 ohms, unbalanced |
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Area code | Tuning |
|
| scale |
|
|
|
|
| 10 kHz step | 9 kHz step |
|
|
|
CEL, CEK, TW, KR | – | |
| kHz | |
|
| |
|
|
|
E2 | ||
| kHz6) | kHz6) |
Antenna | Loop antenna |
|
Intermediate frequency |
| |
| 450 kHz |
|
6)You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down TUNING MODE, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs/Outputs
Video: 1
COMPONENT VIDEO:
Y: 1
PB/CB: 0.7
PR/CR: 0.7
General
Power requirements
Area code | Power requirements |
| ||
CEL, CEK | 230 V AC, 50/60 Hz |
| ||
|
|
|
| |
E2 | 120/220/240 V AC, |
| ||
| 50/60 Hz |
| ||
|
|
|
| |
TW | 110 V AC, 60 Hz |
| ||
|
|
|
| |
KR |
| |||
|
|
| ||
Power output (DIGITAL MEDIA PORT) |
| |||
DC OUT: | 5V, 700 mA |
| ||
Power consumption |
|
|
| |
|
|
| ||
|
|
| ||
Area code | Power consumption |
| Additional | |
|
|
| ||
CEL, CEK, KR | 230 W | |||
| ||||
|
|
|
| |
E2 | 270 W |
| ||
|
|
|
| |
TW | 650 W |
| ||
|
|
| Information | |
| menu is set to “CTRL | |||
Power consumption (during standby mode) |
|
0.3 W (When
“CONTROL” in VIDEO
OFF”.)
AC outlet (Models of area code E2 only) 1 switched, 100 W/
0.4A MAX
Dimensions (width/height/depth) (Approx.)
430 × 157.5 × 351.5 mm including projecting parts and controls
continued
91GB