Sony STRDG910 7

Name Function

HDTS (-ES)/Lights up when the receiver is

(96/24)	decoding DTS signals.
	“DTS-ES” lights up when the
	receiver is decoding DTS-ES
	signals.

“DTS 96/24” lights up when the receiver is decoding DTS 96 kHz/24 bit signals.

Note

When playing a DTS format disc, be sure that you have made digital connections and that INPUT MODE is not set to “ANALOG” (page 71).

IMEMORY Lights up when a memory function, such as Preset Memory (page 67), etc., is activated.

JTuner	Lights up when using the
indicators	receiver to tune in radio stations
	(page 65), etc.
	Note
	“RDS” lights up for models of
	area code CEL, CEK only.

KPreset	Lights up when using the
station	receiver to tune in preset radio
indicators	stations. For details on
	presetting radio stations, see
	page 67.

LD.RANGE Lights up when dynamic range compression is activated (page 45).

MNEO:6	Lights up when DTS Neo:6
	Cinema/Music decoder is
	activated (page 60).

NCOAX	Lights up when INPUT MODE
	is set to “AUTO IN” and the
	source signal is a digital signal
	being input through the
	COAXIAL jack, or when
	INPUT MODE is set to “COAX
	IN” (page 71).

OHDMI	Lights up when the receiver
	recognizes a component
	connected via a HDMI IN jack
	(page 20).

Name Function

PPlayback The letters (L, C, R, etc.)

channel indicate the channels being indicators played back. The boxes around

the letters vary to show how the receiver downmixes the source

sound (based on the speaker settings).

LFront Left

RFront Right

CCenter (monaural)

SL	Surround Left
SR	Surround Right

SSurround (monaural or the surround components obtained

SBL	by Pro Logic processing)
SBL	Surround Back Left
SBR	Surround Back Right
SB	Surround Back (the surround
	back components obtained by
	6.1 channel decoding)
	Example:
	Recording format (Front/
	Surround): 3/2.1
	Output channel: When surround
	speakers are set to “NO” (page
	47)
	Sound Field: A.F.D. AUTO
	SW
	L C	R
	SL	SR

Started Getting

7GB

Contents

Page About This Manual Table of Contents Description and location of parts Page About the indicators on the display Page Rear panel Remote commander RM-AAP017 Page Page Page Page 1: Installing speakers 2: Connecting speakers 3a: Connecting the audio components Page Connecting components with analog audio jacks 3b: Connecting the video components Connecting components with HDMI jacks HDMI features If you connect a Blu-raydisc player Notes on HDMI connections Connecting a TV Page Connecting a DVD player/DVD recorder Connecting a DVD player Connecting a DVD recorder Connecting a satellite tuner/ set-topbox Page Function for conversion of video signals In the video input/output conversion table of the receiver Notes on converting video signals 4: Connecting the antennas 5:Preparing the receiver and the remote Performing initial setup operations Inserting batteries into the remote 6:Selecting the speaker system 7:Calibrating the appropriate settings automatically Before you perform Auto Calibration On setting up the active sub woofer Performing Auto Calibration To cancel Auto Calibration When error codes appear When you select “WARN CHK” When you select “PHASE” A. CAL menu parameters 8:Adjusting the speaker levels and balance Selecting a component To mute the sound To avoid damaging your speakers Listening/Watching a component Watching a DVD Navigating through menus Overview of the menus Page Page Page Adjusting the level Adjusting the equalizer Settings for the surround sound Using the surround back decoding mode Types of the surround back decoding functions Settings for the tuner Settings for the audio Settings for the video Settings for the system Page Page Page Enjoying Dolby Digital and DTS surround sound Types of A.F.D. mode If you connect a sub woofer Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Using only the front speakers Listening to the sound without any adjustment Listening to FM/AM radio Using the controls on the receiver In case of poor FM stereo reception Direct tuning If you cannot tune in a station Presetting radio stations Tuning to preset stations Naming preset stations To create an index name Using the Radio Data System (RDS) Receiving RDS broadcasts Displaying RDS information Description of program types Switching between digital and analog audio Listening to digital sound from other inputs Assignable inputs for digital audio input Enjoying the DIGITAL MEDIA PORT (DMPORT) Connecting the DIGITAL MEDIA PORT adapter To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Listening to a connected component through DMPORT connection Watching a connected component through DMPORT connection Naming inputs Changing the display Using the Sleep Timer Recording using the receiver Programming the remote If programming is unsuccessful, check the following: To clear the memory of the remote To program the remote to control a TV To cancel programming To activate the input after programming To control a CD player To control a DAT deck To control an MD deck To control a tape deck To control an LD player To control a DVD player To control a DVD recorder To control a TV To control a satellite tuner To control a cable box Glossary Page Precautions Troubleshooting Page Video Tuner Remote commander Error messages Specifications Page Page Index