Manuals / Star Micronics / Computer Equipment / Printer

Star Micronics LC24-15 user manual chapter, Printer Control Commands

Models: LC24-15

1 133

Download 133 pages 7.92 Kb

Page 45

chapter 4

chapter 4

PRINTER CONTROL COMMANDS

The printer has two emulation modes: Standard mode and IBM mode.

In standard mode, the printer emulates the functions of the Epson LQ-1050. In IBM mode, the printer emulates the IBM Proprinter XL24. Additional command codes are included as a superset of these emulations.

The emulation is changed by means of DIP switch l-6. When ON, the printer will be in standard mode, and when OFF, the printer will be in IBM emulation mode (see Chapter 3). It is not possible to change the emulation mode by means of software control or the front control panel.

This chapter describes the printer’s control commands. Some commands are common to both the standard and IBM modes. In the descriptions of the com- mands, all commands will be given by function. The name of each command is followed by a table like the one below:

Mode	ASCII			Decimal		Hexadecimal
Both	<ESC>	“x”	“1”	27 120	49	1B	70	31
	<ESC>	“XI’	<l>	27 120	1	1B	78	01
	Mode:			Indicates the mode in which the command is recog-
				nized.
				Std. Standard mode (DIP switch l-6 on)
				IBM IBM mode (DIP switch l-6 off)
				Both Both standard and IBM modes
	ASCII:			Indicates the ASCII coding of the command.
				Control characters are enclosed in pointed brack-
				ets: For example, <O> means character code 0.
	Decimal:			Gives the command in decimal character codes.
	Hexadecimal: Gives the command				in	hexadecimal		character
				codes.

Parameters for which values must be supplied are indicated by italic letters such as n.

Image 45

Star Micronics LC24-15 user manual chapter, Printer Control Commands

Contents

USERS MANUAL LC24-15MULTI-FONT NOT INTENDED FOR SALETrademark Acknowlidgements Self DeclarationMicrosoft BASIC, MS-DOS Microsoft Corporation LQ-1050, LQ-850, LQ-1000 Seiko Epson CorpHOW TO USE THIS MANUAL Chapter 8 - Specifications Chapter 7 - Troubleshooting and maintenanceThis section gives the specifications of your printer Chapter 6 - MS-DOS and your printerFEATURES OF THE PRINTER TABLE OF CONTENTS Chapter 1 SETTINGChapter 2 CONTROL CONTROL COMMANDS Chapter 3 DIP SWITCH SETTINGSChapter 7 TROUBLESHOOTING AND MAINTENANCE TroubleshootingINDEX ChapterSPECIFICATIONS ChapterChapter SETTING UP THE PRINTERLOCATING THE PRINTER Subjects covered in Chapter 1 includeUNPACKING AND INSPECTION Check the carton contentsParts name of the printer SETTING UP Install the ribbon cartridgeMount the platen knob Figure T-4. Removing the top cover Figure 1-5. Installing the ribbon cartrldge3. The ribbon should pass between the print head and the print head shield see Figure l-6 Install the optional IC card Connection Figure 1-9. Replacing the interface board Automatic loading LOADING SINGLE SHEETSFigure 1-77. Loading a single sheet Adjustable paper guides lever IManual loading LOADING AND PARKING FANFOLD FORMS Loading the fanfold formsFlgurs I-13. Thread the fanfold paper over the sprockets Figure I-14. Mounting the paper guide for fanfold forms Loading the paper with pull tractor unit8. Mount the new top cover Paper unparking Paper parkingFigure 7-16. Adjusting for different thicknesses of paper ADJUSTING THE PRINTING GAPBUTTONS AND INDICATORS chapterCONTROL PANEL OPERATIONS ON LINE button PAPER FEED button SET/EJECT PARK buttonPITCH button STYLE button IndicatorsFont style Stay in panel style POWER-UP FUNCTIONSStay in pAe1 FbitchLong test mode Print area test modeStay in panel pitch Stay in panel style Stay in panel pitch and styleHexadecimal dump 10 FOR I=0 TO 20 LPRINT CHR$I 30 NEXT 40 LPRINT 50 END 100 O=INP&H379 IF 0128 THEN 110 OUT &H378,1 OUT &H37A, 5 OUT &H37A,4 Coding for IBM-PC with monochrome display 20 GOSUB120 RETURN Coding for IBM-PC with color adapter 20 GOSUB 100 O=INP&H3BD IF 0128 THEN 110 OUT &H3BC,I OUT &H3BE, 5 OUT &H3BESWITCH COMBINATION FUNCTIONS Top of form Forward micro-feedReverse micro-feed Clearing the buffer D/P SWITCH SETTINGS LOCATION OF THE DIP SWITCHESChapter FUNCTIONS OF THE DIP SWITCHES Switch l-3 Do you want a bottom margin? Switch 1-4 Are you going to use the automatic sheet feeder ASF?If you selected IBM mode, do you want IBM character set #l or #2? Switch 2-1 Does your software download new characters to the printer? Switch 1-8 Do you want an automatic line feed?Switches 2-2 to 2-4 Do you want an international character set? Denmark/Norway when switch l-6 .is OFF and switch l-7 is ONPage MEMO chapter PRINTER CONTROL COMMANDSSelect draft quality characters FONT CONTROL COMMANDSSelect LQ characters Select LQ font styleSelect Optional characters Select Courier charactersSelect Prestige characters Select Ora for charactersSelect italic characters Select Script charactersSelect upright characters Select ornament cha tatterCancel double-strike printing Cancel emphasized printingEmphasized printing Double-s trike printingStart 0 verlining Stop underliningStop 0 verlining SuperscriptCHARACTER SET COMMANDS Cancel superscriptSelect standard character set Select IBM character setSelect character set #2 Enable printing of all character codesSelect international character set Denmark/NorwayCHARACTER SIZE AND PITCH COMMANDS Enable printing of all character codes on next characterSelect slash zero Select normal zeroElite pitch was pressed during power-upHigh-speed elite pitch High-density elite pitchCancel expanded printing Cancel condensed printingCondensed printing Expanded printingExpanded printing for one line Cancel one-line expanded printingSelect character width Select proportional spacingSelect master print mode Select fixed spacingIncrease character spacing “p” ‘VI”Select double or quadruple size Select character sizePrint double-height characters Select character height, width, and line spacing Return to normal height27 73 n Select character type and print pitchSet line spacing to l/8 inch VERTICAL POSITION COMMANDSSet line spacing to 7/60 or 7/72 inch Set line spacing to l/6 inchSet line spacing to n/180 or n/216 inch Set base unit for line spacingSet line spacing to n/60 or nR2 inch Define line spacing to n/72 inchLine feed Execute ESReverse line feed Sleet forward feed modePerform one n/216-inch reverse line feed Perform one n/180-inch or n/2164nch line feedFeed paper n lines Set top of page at current positionSet page length to n inches Set page length to n linesSet top margin Set bottom marginDisable paper-out detector Cancel top and bottom marginsEnable paper-out detector Form feedSet vertical tab stops evetyn lines Set vertical tab stopsSet vertical tab stops in channel Select vertical tab channelHORIZONTAL POSITION COMMANDS Vertical tabSet left margin Set right margin Set left and right marginsCarriage return Set automatic Cancel au toma tic line feedline feed BackspaceFull justify Right justifySet horizontal tab stops Set horizontal tab stop everyn columnsHorizontal tab Reset all tab stopsRelative horizontal tab Relative horizontal tab in inchesAbsolute horizontal tab in inches GRAPHICS COMMANDSAbsolute horizontal tab in columns Print 8-bit normal-density graphicsPrint 8-bit double-density, double-speed graphics Print 8-bit quadruple-density graphicsPrint 249bit hex-density graphics Select graphics mode 42 n02A n0 Se/ect graphics mode Convert graphicsdensity Define download characters DOWNLOAD CHARACTER COMMANDSCopy character set from ROM into RAM card Select download character setSelect ROM character set Cancel last line I OTHER PRINTER CONTROL COMMANDSSet MSB to Accept MSB as isRepeat data Cancel quiet printQuiet print ImmefBa te printSet printer off-line Cancel immediate printSet printer on-line Stop printingBidirectional printing BellUnidirectional prin thg One-line unidirectional printhgAuto feed Reset printerEject paper from ASF Set print start position on ASFMEMO Chapter DOWNLOAD CHARACTERSDEFINING YOUR OWN CHARACTERS Assignjng the character data Assigning a value of character space programmO+ml+m2 Symbol RESTORE1000 LPRINT CHR$27xl 1010DIFFUSION RANGES OF CARS & TELEPHONES MEMO INSTALLING APPLICATION SOFTWARE WITH YOUR PRINTER ChapterMS-DOS AND YOUR PRINTER EMBEDDING PRINTER COMMANDS P-Jt PROGRAMMING THE PRINTER WITH DOS COMMANDS l* *VxlV!*VA 2*c AEDLIN LQELITE.DATPROGRAMMING WITH BASIC LPRINT LPRINTLPRINT LPRINTPage NEXT 23602370 RETURN3250 DATA 31,240DATA 362015,255,192 15,255,192How the program works Double-strike EmphasizedQuad-sized Double-heightModifications for IBM mode TROUBLESHOOTING Chapter 7 TROUBLESHOOTING AND MAINTENANCEPower supply PrintingIf the POWER indicator does not illuminate, check the following If the printout is not what is expected If the print is faint, or uneven, check the followingIf dots are missing in the printing, check the following Paper feeding Is there too much paper in the paper feed hopper or stacker? correct REPLACING THE RIBBON MAINTENANCEREPLACING THE PRINT HEAD Figure 74. Replacing the print head REPLACING THE BATTERY IN THE RAM CARD Chapter SPEClFlCAllONSPage Emulations ..................................... Epson mode Page Chapter CHARACTER SETSSTANDARD CHARACTER SET Page IBM CHARACTER SET #2 “/-3O I l 128 129 ii YCIIBM CHARACTER SET #I Additional characters can be printed by special commands r-T77 IBM SPECIAL CHARACTER SE7INTERNATIONAL CHARACTER SETS INDEX Page style Troubleshooting22,34,40 automaticm2 dl d2 .dx COMMAND SUMMARYFsC“L”nl?L?mlmz “K” nl n2 ml m2nl a2 SCs”Y”nln2mlm2+ nli n2 aa.. “0”‘&w’*“1” MODE CONTROL CODEFUNCTION ‘* co n 4%“.-” “.. “0”