Manuals / Brands / Kitchen Appliance / Freezer / Stoelting / Kitchen Appliance / Freezer

Stoelting 4231G, 4231H REPLACEMENT PARTS, 5.1 HOW TO ORDER PARTS, 5.2PUSH TO FREEZE LIGHT/SWITCH LAMP REPLACEMENT, 5.3CLEAN-OFF-SERVEROCKER SWITCH REPLACEMENT, SECTION, NOTE

1 43

Download 43 pages, 1.28 Mb

SECTION 5

REPLACEMENT PARTS

5.1 HOW TO ORDER PARTSB. Remove the faulty lamp by pulling out the lamp puller (See Fig. 33).

Toassurereceiptoftheproperreplacementparts,supply your dealer or distributor with the following information:

A.Model number of equipment.

B.Serial number of model, stamped on nameplate.

Part Number	Description
324014	Decal Black Arrow
324141	Decal Caution Rotating Blades
324509	DecalCleaning
324548	Decal Ventilation
324346	Decal Caution
324393	Decal – Drip Tray
324803	Decal – Header Panel (Stoelting Logo)
324804	Decal - Header Panel (Stoelting Swirl)
324806	Decal - Header Panel (A & W Logo)
324798	Decal – CLEAN/OFF/SERVE
324125	Decal – Elec. Shock Hazard

C. Part number, part name and quantity needed. Common part names and numbers are listed in this manual.

5.2PUSH TO FREEZE LIGHT/SWITCH LAMP REPLACEMENT

To change a lamp in the PUSH TO FREEZE switch/light follow these simple steps:

A. Grasp the lens with your thumb and forefinger and pull out.

Figure 33. Push To Freeze Light/Switch Assembly

C.To install the new lamp, line up the lamp end with the receptacle and push fully in.

D.Reinstall the lens by pushing firmly in. When installed “PUSH TO” might be right side up.

NOTE

LED light bulbs require correct polarity. If the bulb does not illuminate, remove the bulb, turn 180° and replace.

5.3CLEAN-OFF-SERVE ROCKER SWITCH REPLACEMENT

A. Remove side panel.

WARNING

DISCONNECT FREEZER FROM ELECTRICAL SUPPLY SOURCE BEFORE SERVICING.

21

Contents

Page Page We stock the parts you need CALL Page STOELTING OWNER'S MANUAL FOR MODEL 4231G STOELTING FLOOR GRAVITY FREEZER SOFT-SERVE Stoelting, LLC Page TABLE OF CONTENTS LIST OF ILLUSTRATIONS SECTION INTRODUCTION 1.1DESCRIPTION 1.2SPECIFICATIONS INSTALLATION INSTRUCTIONS 2.1SAFETY PRECAUTIONS 2.2SHIPMENT AND TRANSIT 2.3FREEZER INSTALLATION 2.4ELECTRICAL CONNECTIONS Page INITIAL SET-UPAND OPERATION 3.1OPERATOR’S SAFETY PRECAUTIONS 3.2OPERATING CONTROLS AND INDICATORS A.SPIGOT SWITCH B.CLEAN-OFF-SERVESWITCH will will not C.PUSH TO FREEZE SWITCH 3.3SANITIZING 3.4FREEZE DOWN AND OPERATION 3.5 MIX INFORMATION 3.6 REMOVING MIX FROM FREEZER 3.7CLEANING THE FREEZER 3.8DISASSEMBLY OF FREEZER PARTS Figure 21. Removing Front Door Figure 22. Removing Spigot Figure 23. Removing Auger Supports Figure 24. Auger Shafts Figure 25. Removing O-Ring 3.9CLEANING THE FREEZER PARTS 3.10SANITIZE FREEZER AND FREEZER PARTS 3.11ASSEMBLY OF FREEZER Figure 27. Exploded View of Auger Figure 28. Exploded View of Front Door FINGER TIGHTEN THE CIRCULAR KNOBS EVENLY. DO NOT OVERTIGHTEN KNOBS 3.12 ROUTINE CLEANING MAINTENANCE INSTRUCTIONS 4.1PREVENTIVE MAINTENANCE 4.2FREEZE-UP 4.4EXTENDED STORAGE 4.3CONDENSER SERVICE 4.5TROUBLESHOOTING Page REPLACEMENT PARTS 5.1 HOW TO ORDER PARTS 5.2PUSH TO FREEZE LIGHT/SWITCH LAMP REPLACEMENT 5.3CLEAN-OFF-SERVEROCKER SWITCH REPLACEMENT Page Page Page Page Page Page Page Page Page Page Page Page Page WARRANTY SOFT SERVE / SHAKE FREEZERS 1.Scope: 2.Disclaimer of Other Warranties: 3.Remedies: