Sun Microsystems Gigabit Ethernet MMF/UTP Adapter manual

Low-Profile Power Requirements

TABLE A-7Low-Profile Power Requirements

Specification	Measurement

Typical UTP power consumption	4.95	W (3.3 V @ 1.5 A)
Typical MMF power consumption	3.3v	(1.0A @ 3.3v)

ExpressModule Performance

Specifications

TABLE A-8ExpressModule Performance Specifications

Feature		Specification

Bus type		PCI ExpressModule 1.0a
Bus width		x4 lane PCI Express, operable in x4, x8, x16 slots
Bus speed (x4, encoded rate)		(x4, encoded rate) 10 Gbit/sec uni-directional; 20
		Gbit/sec bi-directional
1	Gbit/sec, 850 nm (MMF)	1000 Mbit/sec (full-duplex)

1	Gbit/sec (UTP)	10/100/1000 Mbit/sec (half-duplex or full-duplex)

66 Sun PCI-Express Dual Gigabit Ethernet MMF/UTP Adapter Installation and User’s Guide • June 2006

Image 100

Contents

Sun Microsystems, Inc Please Recycle Contents Installing the Adapter Configuring ipge and e1000 Driver Parameters Configuring e1000g Driver Parameters Configuring VLANs Specifications Diagnostic Software Index Page FCC Class a Notice Regulatory Compliance StatementsFCC Class B Notice ICES-003 Class a Notice Avis NMB-003, Classe a ICES-003 Class B Notice Avis NMB-003, Classe B Bsmi Class a Notice CCC Class a Notice GOST-R Certiﬁcation Mark Safety Agency Compliance Statement Safety Precautions System Unit Cover Battery WarningRack System Warning Conformité aux normes de sécurité Laser Compliance NoticeCD and DVD Devices Mesures de sécurité Symboles Modification du matérielPositionnement d’un produit Sun Conformité Selv Connexion du cordon d’alimentation Mise en garde relative aux batteries Couvercle de lunité Mise en garde relative au système en rack Einhaltung sicherheitsbehördlicher Vorschriften Aufstellung von Sun-Geräten SELV-KonformitätAnschluss des Netzkabels Warnung bezüglich Batterien Normativas de seguridad Símbolos Modificaciones en el equipoColocación de un producto Sun Cumplimiento de la normativa para instalaciones Selv Cubierta de la unidad del sistema Advertencia sobre las bateríasAdvertencia sobre el sistema en bastidor Nordic Lithium Battery Cautions Dispositivos de CD y DVDNorge Sverige DanmarkPage USA-FCC Class B European UnionPage Xxvii Page Preface How This Document Is Organized Using Unix Commands Typographic Conventions Shell Prompts Documentation, Support, and Training Related DocumentationThird-Party Web Sites Sun Welcomes Your Comments Page Sun PCI-Express Dual Gigabit Ethernet Adapter Overview Hardware Overview LED Displays on the MMF Low-Profile Adapter 1Front Panel Display LEDs for the MMF Low-Profile Adapter Front Panel Display LEDs for the MMF Low-Profile Adapter LED Displays on the UTP Low-Profile Adapter Low-Profile Hardware and Software Requirements2Front Panel Display LEDs for the UTP Low-Profile Adapter Sun PCI-Express Dual Gigabit Ethernet Adapter Overview LED Displays on the MMF ExpressModule Adapter 4Front Panel Display LEDs for the MMF ExpressModule Adapter LED Displays on the UTP ExpressModule Adapter 5Front Panel Display LEDs for the UTP ExpressModule Adapter ExpressModule Hardware and Software Requirements Patches and Updates Page Sun PCI-Express Dual Gigabit Ethernet Adapter Overview Page Installing the Low-Profile Adapter To Install the Low-Profile Adapter To Verify the Installation View the device that you installed List the network devices on your systemView the.properties file for a list of device properties Ok show-nets Your output will be similar to the following example Setting the local-mac-addressProperty Ok setenv local-mac-address? true Installing the ExpressModule Adapter Rebooting the SystemTo Install the ExpressModule Adapter With Power Off To Install the ExpressModule Adapter Using Hot-Plug To Verify the ExpressModule Installation Use the dladm show-devcommand to verify that the link is upPress the Attention button # cfgadmPage Configuring ipge and e1000 Driver Parameters Hardware and Software Overview Setting ipge Driver Parameters Setting Parameters Using the ndd Utility To Specify Device Instances for the ndd Utility Noninteractive and Interactive ModesUse the instance number to select the device # ndd -set /dev/ipge instance To Use the ndd Utility in Interactive Mode To Use the ndd Utility in Noninteractive ModeTo modify a parameter value, use the -setoption Setting the Autonegotiation Mode To Disable Autonegotiation Mode Setting Parameters Using the ipge.conf File Set the adv-autoneg-capparameter to# ndd -set /dev/ipge adv-autoneg-cap Man prtconf To Set Driver Parameters Using an ipge.conf File Locate the path names and the associated instance numbers Link Partner Parameters Set the parameters for the ipge devicesSave the ipge.conf file 1Read-Only Link Partner Capabilities = No 100 Mbit/sec half-duplex transmission To Discover Link Settings Checking ConfigurationsReporting Link Partner Capabilities To Discover Link Partner Capabilities To Check Layer 2 Configuration Use the following command to get the informationIfconfig ipge123000 # kstat ipge0 grep macmtu Device Capabilities Kstat Statistics 3Transmit and Receive Parameters Txmaxpend rxhdrpkts rxmtupkts Rxsplitpkts rxnocompwb Rxnobuf Ipge Driver Parameter, Status, and Descriptions Operational Mode Parameters 5Operational Mode Parameters Gigabit Link Clock Mastership Controls Flow Control Parameters6Read-Write Flow Control Keyword Descriptions 7Forced Mode Parameters Interpacket Gap Parameters 8Parameters Defining enableipg0 and ipg0 Jumbo Frames Interrupt Parameters10RX Blanking Register for Alias Read To Configure Jumbo Frames Using ndd To Configure Jumbo Frames in a Linux EnvironmentPage Configuring e1000g Driver Parameters To Set Driver Parameters Using the e1000g.conf File Setting e1000g Driver Parameters# vi /kernel/drv/e1000g.conf Configuring e1000g Driver Parameters Modify the desired parameter using -3for available settings # reboot # ndd -get /dev/e1000g0 ? Type the kstat command To Check Link Partner Settings$ kstat e1000g0 Configuring e1000g Driver Parameters Driver Parameter, Status, and Descriptions 2e1000g Driver Parameter, Status, and Descriptions Configurable Operational Mode Parameters 3Operational Mode Parameters Upper limit on the maximum MTU size the driver allows Nonconfigurable Operational Mode Parameters 4Nonconfigurable Operational Mode Parameters To Configure Jumbo Frames in a Solaris x86 Environment # ifconfig eth2 xxx.xxx.xx.xxx up # ifconfig eth2 mtuModify the MaxFrameSize value PlumbPage Configuring VLANs Overview of VLANs 1shows an example network that uses VLANs Configuring VLANs To Configure Static VLANs 2Ethernet Tag Header Format # ifconfig ipge123000 plumb up # ifconfig ipge4000 plumb up # ifconfig -aPage Connectors Table A-1LC Connector Link Characteristics Ieee P802.3z Table A-2Cat-5 Connector Link Characteristics Table A-3Connector Link Characteristics Ieee P802.3z Low-Profile Performance Specifications Low-Profile Physical CharacteristicsTable A-4ExpressModule Connector Link Characteristics Table A-5Low-Profile Performance Specifications Low-Profile Power Requirements ExpressModule Performance SpecificationsTable A-7Low-Profile Power Requirements Table A-8ExpressModule Performance Specifications ExpressModule Power Requirements ExpressModule Physical CharacteristicsExpressModule Environmental Requirements Table A-11ExpressModule Environmental Requirements Diagnostic Software SunVTS Diagnostic Software Updating SunVTS to Recognize the Adapter To Update SunVTS to Recognize the Low-Profile AdapterTable B-1SunVTS Documentation To Update SunVTS to Recognize the ExpressModule Adapter Using the SunVTS netlbtestTo Use the netlbtest To Run the FCode Self-Test Diagnostic Using the OpenBoot Prom FCode Self- TestOk setenv auto-boot? false Ok setenv diag-switch? true Reset the system to activate these parameter changesOk reset-all Where Ok setenv diag-switch? false If all of the tests pass, you will see these messages Reset and reboot the system Ok setenv auto-boot? true Setting Up the Driver on a Linux Platform To Set Up the Driver on a Linux Platform Change to the rpm directory Build the man pages optionalLoad e1000 driver for all instances Verify that the driver is loaded # lsmod Tuning for Maximum Performance # dmesgAlias eth2 e1000 Alias eth3 e1000 # ethtool eth3 Sysctl -p ./sysctle1000.conf Net.ipv4.tcpsack = Setting Driver Parameters in a Linux EnvironmentNet.core.netdevmaxbacklog = # rmmod e1000 To Set e1000 Parameters in a Linux Environment# modprobe e1000 option=VAL1, VAL2 Valid Range 0-3 0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx To Configure VLANs in a Linux Environment Configure the e1000 Vlan eth2 in this exampleEnsure that the e1000 module is loaded Insert the Vlan module To Configure Bonding for Multiple e1000 Interfaces Configure bond0 interfaceLoad the bonding driver # modprobe bonding Symbols Index