SUPER MICRO Computer 6015B-3, 6015B-T instruction

SUPERSERVER 6015B-3/6015B-T User's Manual

C-2 Installing the Windows XP/2000/2003 for systems with RAID Functions

New Operating System-Windows XP/2000/2003 Installation

a. Insert Microsoft Windows XP/2000/2003 Setup CD in the CD Driver, and the system will start booting up from CD.

b. Press the <F6> key when the message-" Press F6 if you need to install a third party SCSI or RAID driver" displays.

c. When the Windows XP/2000/2003 Setup screen appears, press "S" to specify additional device(s).

d. Insert the driver diskette-"Intel AA RAID XP/2000/2003 Driver for ESB2 into Drive A: and press the <Enter> key.

e. Choose the Intel(R) ESB2 SATA RAID Controller from the list indicated in the XP/2000/2003 Setup Screen, and press the <Enter> key.

f. Press the <Enter> key to continue the installation process. (If you need to specify any additional devices to be installed, do it at this time.) Once all devices are speciﬁed, press the <Enter> key to continue with the installation.

g. From the Windows XP/2000/2003 Setup screen, press the <Enter> key. The XP/2000/2003 Setup will automatically load all device ﬁles and then, continue the Windows XP/2000/2003 installation.

h. After Windows XP/2000/2003 Installation is completed, the system will auto- matically reboot.

Note: the current version of the ESB2 SATA RAID Utility can only support Windows XP/2000/2003 Operating System.

C-10

Image 116

SUPER MICRO Computer 6015B-3, 6015B-T user manual New Operating System-Windows XP/2000/2003 Installation

Contents

Super Manual Revision 1.0c Release Date December 30 Manual Organization PrefaceAbout This Manual System Safety Advanced Serverboard SetupAdvanced Chassis Setup Bios Preface Table of Contents System Safety Advanced Serverboard Setup Advanced Chassis Setup Sgpio Bios AppendicesPage Chapter Introduction Overview Serverboard Features ProcessorsMemory Onboard SAS 6015B-3 Server Chassis Features SAS/SATA Subsystem Front Control PanelBackplane Cooling System Intel 5000P Chipset System Block Diagram Contacting Super Micro HeadquartersEurope Asia-Paciﬁc Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Outer Rails Locking Tabs Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel Buttons Control Panel LEDs Sata Drives 6015B-T Drive Carrier LEDsSAS Drives 6015B-3 Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Unpacking Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel Front Control Panel Header Pins JF1 I/O Ports Installing MemoryDimm Installation See Figure 3a. Installing Dimm into Slot Memory Support PCI Expansion Slots PCI card installationAdding PCI Cards Serverboard Details Super X7DBR-3/X7DBR-E Layout X7DBR-3/X7DBR-E Quick Reference Jumper Description Default SettingConnector Description Connector Deﬁnitions HDD LED Overheat/Fan Fail LED OH Power Fail LED Reset ButtonPower Button Universal Serial Bus USB0/1 Power Supply Fail Header Serial PortsFan Headers Chassis Intrusion Power LED/Speaker Universal Serial Bus HeadersATX PS/2 Keyboard and PS/2 Mouse Ports Overheat LED Wake-On-LAN Wake-On-Ring JLAN1/2 Ethernet Ports Alarm Reset JARCompact Flash Card PWR Connector Jumper Settings VGA Enable/DisableExplanation Jumpers Cmos Clear Watch Dog Enable/Disable 3rd Power Supply Fail Detect Enable/DisableJlan Enable/Disable Onboard Indicators SAS Controller Enable 6015B-3 onlyCompact Flash Master Slave SMB to PCI Slots Floppy Connector Floppy, IDE, Sata and SAS Drive Connections IDE Connectors Sata Ports SAS Ports X7DBR-3 only Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front and Rear Views Installing a new fan System FansSystem Fan Failure Replacing System Fans Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Removing the Front Bezel SAS/SATA Drive Installation Mounting a SAS/SATA drive in a drive carrier Installing/removing hot-swap SAS/SATA drives Removing a SAS/SATA Drive from the Server SAS/SATA Backplane DVD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supply Removing/Replacing the Power Supply System Bios How To Change the Conﬁguration DataStarting the Setup Utility Chapter Press the Delete key to enter Setup Running SetupMain Bios Setup Main Bios Setup Menu Main Setup Features Bios DateSystem Time System Date Type LBA Mode Control Transfer ModeUltra DMA Mode CHS Format Native Mode Operation Sata Controller ModeSerial ATA Sata RAID Enable Parallel ATA Extended Memory Advanced SetupSystem Memory Boot Features QuickBoot ModeQuietBoot Mode Post Errors Memory Cache Cache System Bios Area Cache Video Bios AreaCache Base 0-512K Cache Base 512K-640K PCI Parity Error Forwarding Reset Conﬁguration DataDiscrete Mtrr Allocation PCI Conﬁguration Enable Master Latency TimerLarge Disk Access Mode Serr Signal Condition Memory Branch Mode Crystal Beach FeaturesClock Spectrum Feature Enabling Multi-Media Timer Advanced Processor Options CPU Speed Device Conﬁguration KBC Clock InputSerial Port a Base I/O Address Interrupt Serial Port BMode Floppy Disk Controller DMI Event Logging Event Log ValidityEvent Log Capacity View DMI Event Log Console Redirection COM Port AddressBaud Rate Console Type CPU Temperature Threshold Hardware Monitor LogicVoltage Monitoring Fan Speed Control Modes CPU Temperature Threshold See note on Hardware Monitor Logic See note on System Event Logging Clear System Event LoggingExisting Event Log Number Event Log Control OS Boot Watch Dog Timer for Loading OS MinutesSystem Event Log/System Event Log List Mode Time Out Option Realtime Sensor Data Supervisor Password Is User Password IsSet Supervisor Password Set User Password Boot Priority Order/Excluded from Boot Orders BootPassword on Boot Exit Appendix a Bios Post Messages System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settings System cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering Setup PS/2 Mouse Boot Summary Screen Fixed Disk nInvalid System Conﬁguration Data Device IRQ conﬂict Press F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupSystem Bios shadowed Video Bios shadowedPage Appendix B Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page ESB2 HostRAID Setup Introduction to Serial ATA and Parallel ATAImportant Notes to the User Serial ATA Sata Intel HostRAID Conﬁgurations Intel Matrix Storage Using the Intel ESB2 Sata RAID Utility Program Creating, Deleting and Resetting RAID Volumes Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility New Operating System-Windows XP/2000/2003 Installation Intel ESB2 I/O Controller Hub Appendix D Adaptec HostRAID SetupX7DBR-E only Conﬁguring Sata RAID Adaptec Embedded Sata with HostRAID Controller Driver Using the Adaptec RAID Conﬁguration Utility ARCUsing the Array Conﬁguration Utility ACU Managing Arrays Conﬁguring Disk Drives To conﬁgure a disk drivePage Page Creating Arrays To create an array Assigning Array Properties To assign properties to the new arrayPage Adding a Bootable Array To make an array bootable Deleting a Bootable Array Adding/Deleting Hotspares To add a Hotspare To delete a Hotspare Viewing Array Properties Rebuilding Arrays To Rebuild an array Deleting Arrays To delete an existing array RAID 1 only-the following prompt is also displayed Using the Disk Utilities To access the disk utilities To format a disk To verify disk media To Exit the Adaptec RAID Conﬁguration Utility Installing Intels ESB2 Driver by Adaptec and the OS Driver/Tool Installation Display Screen Software InstallationInstalling Additional Drivers Conﬁguring Supero Doctor Figure E-1. Supero Doctor Screen Health Information Figure E-2. Supero Doctor Screen Remote Control Page Appendix F System Speciﬁcations Weight Power SupplyMotherboard Chassis Regulatory Compliance