Overheat OH/Fan Fail | SUPER MICRO Computer SuperServer 5016I-TF

SUPERSERVER 5016I-T/5016I-TF User's Manual

Overheat (OH)/Fan Fail

Connect an LED cable to pins 7 and 8 of JF1 to provide warnings for chassis overheating or fan failure. Refer to the table on the right for pin deﬁnitions.

OH/Fan Fail LED

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

7Vcc/Blue UID LED

8OH/Fan Fail LED

OH/Fan Fail Indicator

Status

State Deﬁnition

	Off	Normal
	On	Overheat
	On	Overheat
	Flash-	Fan Fail
	Flash-	Fan Fail
	ing

NIC1/NIC2 (LAN1/LAN2)

The NIC (Network Interface Control- ler) LED connection for LAN port 1 is located on pins 11 and 12 of JF1, and the LED connection for LAN Port 2 is on pins 9 and 10. NIC1 LED and NIC2 LED are 2-pin NIC LED headers. At- tach NIC LED cables to NIC1 LED and NIC2 LED to display network activities for LAN 1 and LAN2. Refer to the table on the right for pin deﬁnitions.

HDD LED

The HDD LED connection is located on pins 13 and 14 of JF1. This LED is used to display HDD activity. See the table on the right for pin deﬁnitions.

Power On LED

The Power On LED connector is lo- cated on pins 15 and 16 of JF1 This connection is used to provide LED indication of power being supplied to the system. See the table on the right for pin deﬁnitions.

LAN1/LAN2 LED

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

	9/11	Vcc
	10/12	Ground
	10/12	Ground

HDD LED

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

13+5V

14HD Active

Power LED

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

15+5V

16Control

5-16

Image 50

SUPER MICRO Computer SuperServer 5016I-TF user manual Overheat OH/Fan Fail, Power On LED

Contents

Super Manual Revision Release Date October 6 Manual Organization PrefaceAbout This Manual Advanced Chassis Setup Bios Preface Table of Contents System Safety Advanced Chassis Setup Bios Page Chapter Introduction Overview Motherboard Features Chassis Features Intel 3400/3420 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PaciﬁcPage Unpacking the System Chapter Server InstallationPreparing for Setup Choosing a Setup Location Rack Precautions Ambient Operating Temperature Rack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack Rails Installing the Chassis Rails Installing the Rack Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Components Checking the Serverboard SetupAccessing the Inside of the System Figure Accessing the Inside of the System Checking the Drives Checking the Drive Bay SetupProviding Power Checking the Airﬂow Chapter System Interface Reset ButtonPower Control Panel Buttons Overheat/Fan Fail HDD Serial ATA Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Motherboard Setup Connecting Data Cables Motherboard InstallationConnecting Cables Installing to the Chassis Connecting Power Cables Connecting the Control Panel Processor and Heatsink Installation I/O Ports Installing the LGA1156 Processor Page Installing a Passive CPU Heatsink Installing the Heatsink Removing the Heatsink Memory Support Installing MemoryDimm Installation Populated Any combination Per Channel Memory Population GuidelinesDDR3 ECC Registered Rdimm Memory Support Dimm Installation Installing a PCI Expansion Card Installing an Expansion Card Motherboard Details X8SIL/X8SIL-F Layout X8SIL/X8SIL-F LED Indicators Number X8SIL/X8SIL-F Jumpers Number Description DefaultX8SIL/X8SIL-F Headers/Connectors Number Description Standby PWR LED Indicator Green Solid on PWR On Processor Power Connector Connector DeﬁnitionsMain ATX Power Supply Connector Power Button Power On LED Overheat OH/Fan Fail Fan Headers Chassis IntrusionATX PS/2 Keyboard and PS/2 Mouse Ports Onboard Speaker Universal Serial Bus USB SpeakerSerial Ports LAN1/LAN2 Ethernet Ports Alarm Reset Onboard Power LEDPower Supply I2C Connector Sgpio 0/1 Headers Explanation of Jumpers Jumper SettingsVGA Enable Cmos Clear USB Wake-Up LAN1/LAN2 Enable/DisablePCI Slot SMB Enable BMC Jumper Ipmi Dedicated LAN LEDs Onboard IndicatorsLAN1/2 LEDs Ipmi Heartbeat LED Sata Ports Floppy ConnectorSata and Floppy Drive Connections Page Chapter Advanced Chassis Setup Static-Sensitive Devices Control Panel Chassis Front View Replacing System Cooling Fans System FansSystem Fan Failure Serial ATA Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays Installing/Removing Sata Drives Mounting a Sata Drive in a Drive Carrier DVD-ROM Drive Installation Installing a DVD-ROM Drive Replacing the Power Supply Power SupplyPower Supply Failure Page Chapter Starting Bios Setup UtilityHow To Change the Conﬁguration Data Introduction Main Setup How to Start the Setup Utility System Memory System Time/System DateProcessor Advanced Setup Conﬁgurations Xboot Feature XProcessor & Clock Options Intel Eist Technology Hardware Prefetcher Available when supported by the CPUActive Processor Cores XAdvanced Chipset Control Xsata / Floppy Conﬁguration PIO Mode IDE Detect Timeout secLBA/Large Mode Type DMA Mode XPCI/PnP Conﬁguration XSuper IO Device Conﬁguration XRemote Access Conﬁguration CPU Temperature CPU Overheat AlarmSystem Temperature XHardware Health Conﬁguration Fan Speed Control Modes Xacpi Conﬁguration Xipmi Conﬁguration X8SIL-F Only XEvent Log Conﬁguration XIntel TXT LT Conﬁguration Bios AS Sclean Bios AC Scheck User Password Security SettingsSupervisor Password Change Supervisor Password Boot Sector Virus Protection Boot SettingsXBoot Device Priority XRemovable Drives Retry Boot DevicesExit Options XCD/DVD Drives Discard Changes and Exit Load Optimal DefaultsLoad Fail-Safe Defaults Discard ChangesPage Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B Installing Windows Installing Windows to a RAID System Installing Windows to a Non-RAID System Bios Appendix C System Speciﬁcations Weight Appendix C System Speciﬁcations