Sylvania A9DF1UH, LD320SS1 owner manual TV Functions  Initial Setup, Before you begin

Español Français English

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

TV Functions

Initial Setup

INTRODUCTION

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoscan, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1 After making all the necessary connections, press [POWER] to turn on the unit.

•This operation may take a few moments.

4 Use [Cursor s/ B] to select the desired location setting, then press [ENTER]

InitialI i i l Setup

Select “Retail” or “Home” for your location.

Retail	Home
Select	ENTER Enter

•Select ”Retail”, the unit will be set up with predefined setting for retail displays. In this setting, the power consumption may possibly exceed the limited requirement of the ENERGY STAR® qualification.

PREPARATION WATCHING TV

2 Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI i i l Setup

Select the language for setup display.			English
Elija el idioma de ajuste.			Español
			Français
Sélectionner langue écran config.
Select	ENTER Enter	SETUP
			Skip

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER]

3 Use [Cursor K/L] to select “Antenna” for TV channels or “Cable” for CATV channels, then press [ENTER]

InitialI i i l Setup

Make sure the antenna is connected to“ANT. IN” jack.			Antenna
Select the destination of “ANT. IN” jack.
			Cable
			Skip
Antenna	Or
Cable
			ANT.IN
Select	ENTER Enter	BACK	SETUP
		Back	Skip

• “Autoscan” will begin.

InitialI i i l Setup

Now the system is scanning for channels,please wait.

Autoscan will take up to 20 minutes to complete.

0%

Analog channels	0ch
Digital channels	0ch

SETUP

Skip

• Select ”Home”, the unit is set to maximize the energy				OPTIONAL
efficiency for home setting and it can be adjusted
through a choice of picture and sound quality
according to your preference.				SETTING
• When the initial setup is completed, the lowest
memorized channel with the confirmation message
of the location setting will be displayed on the TV
contact the Cable provider.				OPERATING
screen.
Note:
• If you are not receiving a signal from your cable service,
• If you press [POWER] or [SETUP] during autoscan, this				DVD
setting will be canceled.
• The initial autoscan function can be executed for either
“Antenna” or “Cable” only once. When you change the
connection (Antenna / Cable), set autoscan again.				DVD
Refer to page 20.
• If there is no signal input from the antenna terminal and				SETTING
no operation for several seconds after you turn on the unit,
“Helpful Hints” appears. Follow the instructions listed on
the TV screen.
	InitialI i i l Setup
	No channel is registered.		Retry
	Try Autoscan again?		Later	TROUBLESHOOTING
	Verify that you have a cable connected to the " ANT. IN" jack
	on the back of the TV, the channel installation process
	searches this connection. If you are using a cable or satellite
	box, please confirm the input which you have connected the
	box and press the “INPUT SELECT” key on the remote control to
	select the appropriate source input.
	Select	SETUP	Skip
		ENTER Enter
• You must set ”Home” in step 4. Otherwise, the settings
of picture and sound quality you adjusted will not be
memorized after you turn off the unit.
After an initial setup is completed...				INFORMATION
• If you want to scan the channels automatically again,
refer to “Autoscan” on page 20.
• You can add the desired channels unmemorized by
“Autoscan”. Refer to “Manual Register” on page 21.
• If you want to change to another language, refer to
“Language Selection” on page 22.
• If you want to change the location setting, refer to
“Location” on page 33.

15

EN