Video Cassette Recorder VCR, VCR Playback | TANDBERG 7000 guide

TANDBERG Videoconferencing System

Peripherals

Video Cassette Recorder (VCR)

VCR - Playback

TIP

Video

Codec: Video Input 4 (VCR)

VCR: Video Output

TO SIMPLIFY CONNECTING A VCR, THE NECESSARY CONNECTORS ARE MARKED ‘VCR’

Audio

Codec: Audio Input 6 (VCR)

VCR: Audio Output

vcr

Press VCR to activate the VCR input.

For playback, connect a cable between Video Out on the VCR and ‘VideoIn 4 (VCR)’ on the system. Connect a cable between Audio Out on the VCR and the VCR audio input on the system.

Make sure that ‘Audio In 6 (VCR)’ is On (see ‘Audio Settings’). If audio from VCR is too low, this level can be adjusted in ‘Audio Settings’, ‘Inputs’, ‘Level Settings’. The audio from the VCR will be audible in the local speaker system.

The audio from the VCR and your microphone(s) will be mixed and sent to the far end. When a person talks on either local or far end, the VCR audio level will be reduced to make it easier to comment on a video recording when ‘Audio Settings’, ‘Mix Mode: Auto’.

VCR - Recording

When recording, the VCR will record the video as it appears on the main monitor, the local audio and the audio from the far end.

Video

Codec: Video Output 3

VCR: Video Input

Audio

Codec: Audio Output 3

VCR: Audio Input

When recording a videoconference, connect a cable between ‘VideoOut 3’ on the system and Video In on the VCR. Connect a cable between ‘AudioOut 3’ on the system and Audio In on the VCR.

109

Image 109

TANDBERG 7000 user manual Video Cassette Recorder VCR, VCR Playback, VCR Recording

Contents

Page After image lagging due to remaining electrical load Solving after-image lagging problemsAfter-image lagging due to sticking Trademarks and copyright Equipment Markings Operator Safety Summary Contents Peripheral Equipment 103 Advanced useAppendices 112 Index 123 Introduction Main Menu Menu structure At a glance the Tandberg 7000 system Tandberg 7000 Videoconferencing System Monitors V.E. II CameraCodec Remote control Tandberg Natural Audio Module Table microphone Unpacking and mounting Precautions Unpacking and mounting of the base Column and Foot Lift the monitor frame out of the transport case Unpacking and installing the monitor frame Power cable Connecting cablesMicrophone cable Namii Audio Module audio cable 5b. Isdn cable using the PRI interface 5a. Isdn cables using BRI interface5c. Other networks using the External Network interface LAN cable Monitor back cover ‘Terminal Settings’, ‘Software Options’ System configuration Isdn configuration LAN configuration Welcome menu System start-up Basics Making a call Making and ending callsIsdn call LAN call Using sub-address / extension address / MCU password Access Code Dialing TWO Numbers Selecting / setting default quality bandwidth Selecting / setting default network End a call Answer a callCorrecting keying mistakes Press D Irectory to bring up the following menu Directory Edit Entry Add New EntryDelete Entry Delete Entry Add Site Add MultiSite Entry View outgoing video selfview Adjusting volumeMicrophone on/off On Screen Symbols Do Not Disturb / Sleep Mode Controlling the Main Camera Focusing cameraSelecting video sources Moving / zooming camera Voice Activated Camera Positioning SetupActivating Deactivating Selecting presets PresetsStoring presets Storing preset 10 to Main cam Aux Doc cam Vcr Far end camera control Fecc Sending a snapshot Sending and receiving snapshotsViewing a snapshot Receiving a snapshot Add Duo Video Duo Video End a Duo Video call LAN 3MB MultiSite MCU MultiSite cascading Establishing MultiSite meetings using Directory Press C Onnect Adding an extra site dial out Adding an extra site dial Disconnecting sites from a conference PC SoftPresenter PC Presenter Web-interface Press MENU, select ‘Terminal Settings’, ‘LAN Settings’ Streaming Text Chat / Closed CaptioningSnapshots Main menu Menu Password Call quality Advanced call quality Duo Video Mode Presentation ModePresentations Duo Video Quality Duo Video / Snapshot Source Duo Video NumberAuto-Display Snapshot Snapshot Filter Autoanswer UtilitiesFar end camera control Dual Monitor Welcome Menu Auto-PIPContinuous Presence MCU status line Web Snapshots MCU services When MultiSite When connected to an MCUQuick Menu Release floor Request floorTerminal Names View site # Chair control Audio Inputs Audio Settings Level Settings Mix Mode Audio Outputs Level Settings Outputs Noise Reduction Echo Control Motion Room Size Tips for improving the echo canceller performance Automatic Gain Control AGC Settings Restore Audio Defaults Alert Tones & VolumeAlert Speaker Key Tones Camera Tracking Mode Video SettingsDocument Camera Focus Monitor SettingsCamera Brightness Whitebalance Video Name VGA Out VGA SettingsVGA Out Quality Password VNC SettingsStart using VNC Address Network Configuration Terminal SettingsPage Isdn switch type ISDN-BRI Settings Line setup Advanced Isdn settings Subaddress Parallel dial MSN Multiple Subscriber NumberSend Own Numbers Sending Complete PRI Switch Type ISDN-PRI SettingsNumber Low Channel Channel Hunting Max ChannelsHigh Channel Search Advanced Isdn Settings Line Settings Advanced ISDN-PRI Settings Call Control Leased E1/T1 SettingsNetwork Interface Start Channel External network settings Network clocking Cable Specification Address Port LAN SettingsTTL/Router Hops Streaming Source How to view streamingAllow Remote Start Announcements Settings NAT Address Advanced H.323 SettingsPorts QoS Type IP Type of Service TOSIP Precedence Diffserv IP-assignment IP SettingsIP-address IP-subnet mask Ethernet Speed Snmp SettingsRestart Snmp Trap Host Access Code Call SettingsIncoming MCU calls Incoming telephone calls Encryption Secure Conference Encryption Mode Network Profiles Max Call Length Dataport configuration Dataport Software Options LanguageFollowing options are available System info DiagnosticsChannel status Most common cause codes for Isdn are Cause codes Call status Restore defaults Test subsystem View current settingsIP Address Conflict Check Far End Loop Isdn only Interfaces Peripheral Equipment Video Outputs Video InputsAudio Inputs Audio Outputs Dual Monitor Set ‘VGA Out Dual’ in ‘VGA Settings’ menuSet ‘Dual Monitor On’ in ‘Utilities’ menu Document camera Multiple controllable cameras Tracker AudioScience microphone VCR Playback Video Cassette Recorder VCRVCR Recording Extra fixed cameras Telephone Add-On Additional microphones Appendices Using Telesync TS-256 SW56/ISDN adapter Appendix 2 Connecting the system to the Switched 56 network Using CSU adapter Appendix 3 Connecting the system to PRI/T1 Appendix 4 Environmental considerations Loudspeaker volumeIris control and lighting Background How to prepare a typical room for videoconferencing Guidelines for setting up videoconferencing rooms Description of the different files Appendix 5 Using the file system Custom logos Appendix 6 Security Access Code Streaming password Encryption Appendix 7 Declaration of Conformity Index Index Tandberg Videoconferencing System 125