System configuration | TANDBERG 7000 guide

TANDBERG Videoconferencing System	Installation

System configuration

•Switch the system on by connecting the power cable to an electrical distribution socket.

•After the system has performed a self-test routine, product logo and a ‘Welcome’ menu will be displayed on the monitor.

NOTE

THESE SETTINGS ARE ESSENTIAL FOR OPTIMAL SYSTEM SET-UP.

•Enabled but unused ISDN lines (lines not active) should be disabled. Select the Quick Key ‘System Info’ (on the remote control) to view line status.

menu	PRESS MENU ON THE REMOTE CONTROL. SELECT THE MENU ‘TERMINAL SETTINGS’, ‘NETWORK’, ‘ISDN-BRISETTINGS’. SELECT THE
	RELEVANT ‘LINE SETUP’ MENU AND SET ‘ENABLED: OFF’.

•Enter System Name to identify the system during an MCU conference. Select ‘Utilities’, ‘System Name’ and enter the name using the number keys (as on a mobile phone).

•Select the language you want to use in ‘Terminal Settings’, ‘Language’.

•Please make sure that ‘Dual Monitor’ is set to ‘On’ in the ‘Utilities’ menu.

•To activate MultiSite and/or Presenter, enter an option key (see paperwork accompanying your system), see

‘Terminal Settings’, ‘Software Options’.

connect • Press CONNECT on the remote control. A dial tone should be heard if the network is active.

• Press the VOLUME keys on the remote control to adjust the volume to a level of your choice.

19

Image 19

TANDBERG 7000 user manual System configuration, ‘Terminal Settings’, ‘Software Options’

Contents

Page After image lagging due to remaining electrical load Solving after-image lagging problemsAfter-image lagging due to sticking Trademarks and copyright Equipment Markings Operator Safety Summary Contents Peripheral Equipment 103 Advanced useAppendices 112 Index 123 Introduction Main Menu Menu structure At a glance the Tandberg 7000 system Tandberg 7000 Videoconferencing System Monitors V.E. II CameraCodec Remote control Tandberg Natural Audio Module Table microphone Unpacking and mounting Precautions Unpacking and mounting of the base Column and Foot Lift the monitor frame out of the transport case Unpacking and installing the monitor frame Namii Audio Module audio cable Connecting cablesPower cable Microphone cable LAN cable 5a. Isdn cables using BRI interface5b. Isdn cable using the PRI interface 5c. Other networks using the External Network interface Monitor back cover ‘Terminal Settings’, ‘Software Options’ System configuration Isdn configuration LAN configuration Welcome menu System start-up Basics LAN call Making and ending callsMaking a call Isdn call Using sub-address / extension address / MCU password Access Code Dialing TWO Numbers Selecting / setting default quality bandwidth Selecting / setting default network End a call Answer a callCorrecting keying mistakes Press D Irectory to bring up the following menu Directory Delete Entry Add New EntryEdit Entry Delete Entry Add Site Add MultiSite Entry View outgoing video selfview Adjusting volumeMicrophone on/off On Screen Symbols Do Not Disturb / Sleep Mode Moving / zooming camera Focusing cameraControlling the Main Camera Selecting video sources Deactivating SetupVoice Activated Camera Positioning Activating Storing preset 10 to PresetsSelecting presets Storing presets Main cam Aux Doc cam Vcr Far end camera control Fecc Receiving a snapshot Sending and receiving snapshotsSending a snapshot Viewing a snapshot Add Duo Video Duo Video End a Duo Video call LAN 3MB MultiSite MCU MultiSite cascading Establishing MultiSite meetings using Directory Press C Onnect Adding an extra site dial out Adding an extra site dial Disconnecting sites from a conference PC SoftPresenter PC Presenter Web-interface Press MENU, select ‘Terminal Settings’, ‘LAN Settings’ Streaming Text Chat / Closed CaptioningSnapshots Main menu Menu Password Call quality Advanced call quality Duo Video Quality Presentation ModeDuo Video Mode Presentations Snapshot Filter Duo Video NumberDuo Video / Snapshot Source Auto-Display Snapshot Dual Monitor UtilitiesAutoanswer Far end camera control MCU status line Auto-PIPWelcome Menu Continuous Presence Web Snapshots MCU services When MultiSite When connected to an MCUQuick Menu View site # Request floorRelease floor Terminal Names Chair control Audio Inputs Audio Settings Level Settings Mix Mode Audio Outputs Level Settings Outputs Noise Reduction Echo Control Motion Room Size Tips for improving the echo canceller performance Automatic Gain Control AGC Settings Key Tones Alert Tones & VolumeRestore Audio Defaults Alert Speaker Camera Tracking Mode Video SettingsDocument Camera Whitebalance Monitor SettingsFocus Camera Brightness Video Name VGA Out VGA SettingsVGA Out Quality Address VNC SettingsPassword Start using VNC Network Configuration Terminal SettingsPage Isdn switch type ISDN-BRI Settings Line setup Advanced Isdn settings Subaddress Sending Complete MSN Multiple Subscriber NumberParallel dial Send Own Numbers PRI Switch Type ISDN-PRI SettingsNumber Search Channel Hunting Max ChannelsLow Channel High Channel Advanced Isdn Settings Line Settings Advanced ISDN-PRI Settings Start Channel Leased E1/T1 SettingsCall Control Network Interface External network settings Network clocking Cable Specification Address Port LAN SettingsTTL/Router Hops Announcements How to view streamingStreaming Source Allow Remote Start Settings NAT Address Advanced H.323 SettingsPorts Diffserv IP Type of Service TOSQoS Type IP Precedence IP-subnet mask IP SettingsIP-assignment IP-address Snmp Trap Host Snmp SettingsEthernet Speed Restart Incoming telephone calls Call SettingsAccess Code Incoming MCU calls Encryption Secure Conference Encryption Mode Network Profiles Max Call Length Dataport configuration Dataport Software Options LanguageFollowing options are available System info DiagnosticsChannel status Most common cause codes for Isdn are Cause codes Call status Restore defaults Far End Loop Isdn only View current settingsTest subsystem IP Address Conflict Check Interfaces Peripheral Equipment Audio Outputs Video InputsVideo Outputs Audio Inputs Dual Monitor Set ‘VGA Out Dual’ in ‘VGA Settings’ menuSet ‘Dual Monitor On’ in ‘Utilities’ menu Document camera Multiple controllable cameras Tracker AudioScience microphone VCR Playback Video Cassette Recorder VCRVCR Recording Extra fixed cameras Telephone Add-On Additional microphones Appendices Using Telesync TS-256 SW56/ISDN adapter Appendix 2 Connecting the system to the Switched 56 network Using CSU adapter Appendix 3 Connecting the system to PRI/T1 Background Loudspeaker volumeAppendix 4 Environmental considerations Iris control and lighting How to prepare a typical room for videoconferencing Guidelines for setting up videoconferencing rooms Description of the different files Appendix 5 Using the file system Custom logos Appendix 6 Security Access Code Streaming password Encryption Appendix 7 Declaration of Conformity Index Index Tandberg Videoconferencing System 125