Snmp Settings, Ethernet Speed, Restart | TANDBERG 7000 specification

Advanced use	TANDBERG Videoconferencing System
Ethernet Speed
Auto	The codec will auto-detect the speed/duplex on the LAN.
10/Half	The codec will connect to the LAN using 10Mbps speed/Half Duplex.
10/Full	10 Mbps speed/Full Duplex.
100/Half	100 Mbps speed/Half Duplex.
100/Full	100 Mbps speed/Full Duplex.

Restart

Pressing the Quick key ‘Restart’ will restart your system without having to use the On/Off switch on the codec. If IP-assignment is changed, it is sufficient to use this Quick key to restart the system.

SNMP Settings

SNMP Trap Host

SNMP (Simple Network Management Protocol) is used for monitoring and configuring of different units in a network. The codec’s SNMP Agent responds to requests from SNMP Managers (a PC program etc.). SNMP traps are generated by the agent to inform the manager about important events.

SNMP Trap Host identifies the IP-address of the SNMP manager.

Traps can be sent to multiple SNMP Trap Hosts. Enter the IP address of up to three SNMP managers. All traps will then be sent to the hosts listed.

SNMP Community

SNMP Community names are used to authenticate SNMP requests. SNMP requests must have a ‘password’ in order to receive a response from the SNMP agent in the codec.

NOTE THE SNMP COMMUNITY NAME IS CASE SENSITIVE.

92

Image 92

TANDBERG 7000 user manual Snmp Settings, Ethernet Speed, Restart, Snmp Trap Host, Snmp Community

Contents

Page After-image lagging due to sticking Solving after-image lagging problemsAfter image lagging due to remaining electrical load Trademarks and copyright Operator Safety Summary Equipment Markings Contents Appendices 112 Index 123 Advanced usePeripheral Equipment 103 Introduction Menu structure Main Menu Tandberg 7000 Videoconferencing System At a glance the Tandberg 7000 system Codec V.E. II CameraMonitors Remote control Table microphone Tandberg Natural Audio Module Precautions Unpacking and mounting Unpacking and mounting of the base Column and Foot Unpacking and installing the monitor frame Lift the monitor frame out of the transport case Connecting cables Power cableMicrophone cable Namii Audio Module audio cable 5a. Isdn cables using BRI interface 5b. Isdn cable using the PRI interface5c. Other networks using the External Network interface LAN cable Monitor back cover System configuration ‘Terminal Settings’, ‘Software Options’ Isdn configuration LAN configuration System start-up Welcome menu Basics Making and ending calls Making a callIsdn call LAN call Access Code Using sub-address / extension address / MCU password Selecting / setting default quality bandwidth Dialing TWO Numbers Selecting / setting default network Correcting keying mistakes Answer a callEnd a call Directory Press D Irectory to bring up the following menu Add New Entry Edit EntryDelete Entry Delete Entry Add MultiSite Entry Add Site Microphone on/off Adjusting volumeView outgoing video selfview On Screen Symbols Do Not Disturb / Sleep Mode Focusing camera Controlling the Main CameraSelecting video sources Moving / zooming camera Setup Voice Activated Camera PositioningActivating Deactivating Presets Selecting presetsStoring presets Storing preset 10 to Far end camera control Fecc Main cam Aux Doc cam Vcr Sending and receiving snapshots Sending a snapshotViewing a snapshot Receiving a snapshot Duo Video Add Duo Video End a Duo Video call MultiSite MCU LAN 3MB Establishing MultiSite meetings using Directory MultiSite cascading Adding an extra site dial out Press C Onnect Disconnecting sites from a conference Adding an extra site dial PC Presenter PC SoftPresenter Press MENU, select ‘Terminal Settings’, ‘LAN Settings’ Web-interface Snapshots Text Chat / Closed CaptioningStreaming Menu Password Main menu Call quality Advanced call quality Presentation Mode Duo Video ModePresentations Duo Video Quality Duo Video Number Duo Video / Snapshot SourceAuto-Display Snapshot Snapshot Filter Utilities AutoanswerFar end camera control Dual Monitor Auto-PIP Welcome MenuContinuous Presence MCU status line Web Snapshots MCU services Quick Menu When connected to an MCUWhen MultiSite Request floor Release floorTerminal Names View site # Chair control Audio Settings Audio Inputs Mix Mode Level Settings Level Settings Outputs Audio Outputs Echo Control Noise Reduction Room Size Motion Automatic Gain Control AGC Settings Tips for improving the echo canceller performance Alert Tones & Volume Restore Audio DefaultsAlert Speaker Key Tones Document Camera Video SettingsCamera Tracking Mode Monitor Settings FocusCamera Brightness Whitebalance Video Name VGA Out Quality VGA SettingsVGA Out VNC Settings PasswordStart using VNC Address Terminal Settings Network ConfigurationPage ISDN-BRI Settings Isdn switch type Line setup Advanced Isdn settings Subaddress MSN Multiple Subscriber Number Parallel dialSend Own Numbers Sending Complete Number ISDN-PRI SettingsPRI Switch Type Channel Hunting Max Channels Low ChannelHigh Channel Search Line Settings Advanced Isdn Settings Advanced ISDN-PRI Settings Leased E1/T1 Settings Call ControlNetwork Interface Start Channel External network settings Cable Specification Network clocking TTL/Router Hops LAN SettingsAddress Port How to view streaming Streaming SourceAllow Remote Start Announcements Settings Ports Advanced H.323 SettingsNAT Address IP Type of Service TOS QoS TypeIP Precedence Diffserv IP Settings IP-assignmentIP-address IP-subnet mask Snmp Settings Ethernet SpeedRestart Snmp Trap Host Call Settings Access CodeIncoming MCU calls Incoming telephone calls Encryption Mode Encryption Secure Conference Max Call Length Network Profiles Dataport configuration Dataport Following options are available LanguageSoftware Options Channel status DiagnosticsSystem info Cause codes Most common cause codes for Isdn are Restore defaults Call status View current settings Test subsystemIP Address Conflict Check Far End Loop Isdn only Peripheral Equipment Interfaces Video Inputs Video OutputsAudio Inputs Audio Outputs Set ‘Dual Monitor On’ in ‘Utilities’ menu Set ‘VGA Out Dual’ in ‘VGA Settings’ menuDual Monitor Document camera Multiple controllable cameras AudioScience microphone Tracker VCR Recording Video Cassette Recorder VCRVCR Playback Telephone Add-On Extra fixed cameras Additional microphones Appendices Appendix 2 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapter Appendix 3 Connecting the system to PRI/T1 Using CSU adapter Loudspeaker volume Appendix 4 Environmental considerationsIris control and lighting Background Guidelines for setting up videoconferencing rooms How to prepare a typical room for videoconferencing Appendix 5 Using the file system Description of the different files Custom logos Access Code Appendix 6 Security Streaming password Encryption Appendix 7 Declaration of Conformity Index Index Tandberg Videoconferencing System 125