Manual Range Select, Range Setpoints | Teledyne 3000ZA-3X instruction

Operation	3000ZA-3X

4.7.2Manual Range Select

-----------------------

Man Rng: R1

-----------------------

Pressing ENTER causes the range R1 or R2 or R3 to start flashing. Then pressing UP or DOWN cycles through the 3 ranges. The selected range is the effective range if the Range Select (above) is set to Man(ual).

4.7.3Range Setpoints

-----------------------

R1: 0-1000.00 ppm

-----------------------

Pressing ENTER causes the value to the right of Rn: to start flashing. Then pressing UP or DOWN adjusts the value. These are the range setpoints for R1, R2, and R3. They may be set to a value in the range of 1.00 ppm to 100% with the stipulation that the each range must have a setpoint equal to or greater than the setpoint of the range below it plus 1ppm.

Teledyne Analytical Instruments

44

Image 56

Teledyne 3000ZA-3X operating instructions Manual Range Select, Range Setpoints

Contents

Model 3000ZA-3X 3000ZA-3X Specific Model Information Important Notice Safety Messages 3000ZA-3X Vii Table of Contents Testing the System Maintenance Appendix Model 3000ZA Front Panel Model 3000ZA Rear Panel List of Tables Xii Main Features of the Analyzer IntroductionOverview Typical Applications Model Designations Introduction 3000ZA-3X Front Panel Operator Interface Model 3000ZA Front Panel Function Keys Data Entry KeysDigital Meter Display Alphanumeric Interface Screen Standby Button Access DoorRear Panel Equipment Interface ∙ 50-Pin Equipment Interface Port Optional Operational Theory IntroductionZrO2 Sensor Principles of Operation Sample System Operational Theory 3000ZA-3X Electronics and Signal Processing Zirconium Oxide Sensor Application Notes Operational Theory 3000ZA-3X Component Location Electronic Block Diagram Mounting the Analyzer InstallationUnpacking the Analyzer Installation 3000ZA-3X Rear Panel Connections Gas Connections Installation3000ZA-3X Zero in and Span in Optional Electrical Connections Equipment Interface Connector Pin Arrangement Threshold Alarm Analog Output Connections System Alarm Alarm Relay Contact Pins Remote Calibration Connections Range ID Relay Connections Remote Probe Connections FET Series Resistance 2.3 RS-232 Port Commands via RS-232 Input Installing the Zirconium Oxide Sensors Testing the System Operation Keys Description Using the Data Entry and Function ButtonsStyle Conventions Enter Escape System Menu Menu/Screen StructureAnalyze Screen Hierarchy of Available Functions Password routine Enter Password T aChange Password Enter New Password T a Logout Routine Model Routine Filter Routine Analog-Out Adjust RoutineSelf-Test Routine 20mA Gain 20mA Limit False Track in Cal Yes Change Stream Auto-Calibration TimerSpan Menu Span Value Span TimerSpan Sensor Span Finish Span Auto FinishSpan Begin Span Begin Begin Span? Zero Value Zero MenuZero Finish Zero Timer Zero Timer 7 minZero Begin Zero Begin Begin Zero? Alarms Menu Alarm ActiveAlarm Polarity AL-1 NON-LATCHING AL-1 20.00 ppm AL-2 Active Alarm Failsafe Alarm LatchingAlarm Setpoint AL-1 80.00 ppm Range Select Auto Range MenuRange Select Manual Range Select Range Setpoints Maintenance Routine MaintenanceSensor Replacement Removing the Sensor Maintenance 3000ZA-3X Fuse Replacement Sensor Block with Middle Sensor Installed System Self Diagnostic Test Self-Test Result Display Major Internal Components Rear Panel Removal Remove only those screws marked with an Cleaning Troubleshooting Trace Oxygen Analyzer Maintenance Maintenance 3000ZA-3X Teledyne Analytical Instruments Specifications Appendix Operating Temperature 5-35 C Recommended 2-Year Spare Parts List Qty Part Number Description Drawing List 19-inch Relay Rack Panel Mount Application Notes Flow Rate Recommendations Restriction Devices BY-PASS Conversions