Manuals / Teledyne / Personal Care / Oxygen Equipment

Teledyne 3000ZA-3X Self-Test Routine, Filter Routine, Analog-Out Adjust Routine

Models: 3000ZA-3X

1 72

Download 72 pages 26.68 Kb

Page 46

Operation	3000ZA-3X

V1.0

-----------------------

Entering the MODEL screen causes the above screen to be displayed for 3 seconds. There are no modifiable parameters.

4.3.6 Self-Test Routine

-----------------------

Begin Self-Test?

ENTER-YES ESCAPE-NO

-----------------------

Pressing ENTER causes the analyzer to run the same diagnostic that runs on start-up. See section 5.4 for results display.

4.3.7 Filter Routine

-----------------------

Digital Filter ->Index: 5

-----------------------

Pressing ENTER causes the number after 'Index:' to start

flashing. Then pressing UP or DOWN selects a number ranging from 1 to 10. Lower filter values cause the analyzer to converge on new inputs more quickly, but also allow more noise in the sample.

4.3.8 Analog-Out Adjust Routine

-----------------------

4-20mA Offset: 0

Teledyne Analytical Instruments

34

Image 46

Teledyne 3000ZA-3X operating instructions Self-Test Routine, Filter Routine, Analog-Out Adjust Routine

Contents

Model 3000ZA-3X 3000ZA-3X Specific Model Information Important Notice Safety Messages 3000ZA-3X Vii Table of Contents Testing the System Maintenance AppendixModel 3000ZA Front Panel Model 3000ZA Rear PanelList of Tables XiiOverview Main Features of the AnalyzerIntroduction Typical ApplicationsModel Designations Introduction 3000ZA-3XFront Panel Operator Interface Model 3000ZA Front PanelDigital Meter Display Function KeysData Entry Keys Alphanumeric Interface ScreenRear Panel Equipment Interface Access DoorStandby Button ∙ 50-Pin Equipment Interface Port OptionalZrO2 Sensor Operational TheoryIntroduction Principles of OperationSample System Operational Theory 3000ZA-3XElectronics and Signal Processing Zirconium Oxide Sensor Application NotesOperational Theory 3000ZA-3X Component Location Electronic Block Diagram Unpacking the Analyzer InstallationMounting the Analyzer Installation 3000ZA-3X Rear Panel Connections Gas ConnectionsInstallation3000ZA-3X Zero in and Span in Optional Electrical ConnectionsEquipment Interface Connector Pin Arrangement Threshold Alarm Analog Output ConnectionsSystem Alarm Alarm Relay Contact PinsRemote Calibration Connections Range ID Relay Connections Remote Probe Connections FET Series Resistance 2.3 RS-232 PortCommands via RS-232 Input Installing the Zirconium Oxide Sensors Testing the SystemOperation Style Conventions Using the Data Entry and Function ButtonsKeys Description Enter EscapeAnalyze Screen Menu/Screen StructureSystem Menu Hierarchy of Available Functions Change Password Password routineEnter Password T a Enter New Password T aLogout Routine Model RoutineSelf-Test Routine Analog-Out Adjust RoutineFilter Routine 20mA Gain 20mA Limit False Track in Cal Yes Span Menu Auto-Calibration TimerChange Stream Span Sensor Span TimerSpan Value Span Begin Span FinishSpan Auto Finish Span Begin Begin Span?Zero Finish Zero MenuZero Value Zero Begin Zero TimerZero Timer 7 min Zero Begin Begin Zero?Alarm Polarity Alarms MenuAlarm Active AL-1 NON-LATCHING AL-1 20.00 ppm AL-2 ActiveAlarm Setpoint Alarm FailsafeAlarm Latching AL-1 80.00 ppmRange Select Range MenuRange Select Auto Manual Range Select Range SetpointsSensor Replacement MaintenanceRoutine Maintenance Removing the SensorMaintenance 3000ZA-3X Fuse Replacement Sensor Block with Middle Sensor InstalledSystem Self Diagnostic Test Self-Test Result DisplayMajor Internal Components Rear Panel Removal Remove only those screws marked with anCleaning TroubleshootingTrace Oxygen Analyzer Maintenance Maintenance 3000ZA-3X Teledyne Analytical Instruments Specifications AppendixOperating Temperature 5-35 C Recommended 2-Year Spare Parts List Qty Part Number DescriptionDrawing List 19-inch Relay Rack Panel MountApplication Notes Flow Rate RecommendationsRestriction Devices BY-PASS Conversions