Table Of Contents, I. 0 INTRODUCTION, Installation | Teledyne 460H

TABLE OF CONTENTS
SAFETY MESSAGES		II
TABLE OF CONTENTS		III
FIGURES		V
TABLES		VI
I. 0 INTRODUCTION		7
1. 1 PREFACE		7
1.2 WARRANTY POLICY		8
1.3 PRINCIPLE OF OPERATION		9
1.4 SPECIFICATIONS		10
2.0 INSTALLATION		11
2.1 MECHANICAL INSTALLATION		11
2.2 PNEUMATIC CONNECTIONS		12
2.3 AC POWER CONNECTION		13
2.4	ELECTRICAL I/O CONNECTIONS	14
2.4.1	Analog Output	14
2.4.2	Digital Status Outputs	15
2.4.3	Control Inputs	16
2.4.4	RS232/RS485 Serial Communications Port	17
3.0 STARTUP		18
4.0 OPERATION		19
4.1 FRONT PANEL DISPLAY		19
4.1.1 O3 readout		19
4.1.2 Pressure Display		19
4.1.3 Zero Calibration		19
4.1.4 Status LED’s		19
4.2 AUTO-ZEROOPERATION (OPTIONAL)		20
4.2.1 Auto-Zero Installation		20
4.2.2 Auto-Zero Function		20
4.2.3 Auto Zero Error		20
5.0 SERIAL COMMUNICATIONS		21
5.1 SERIAL PORT CONFIGURATION		21
5.2 COMMAND SYNTAX		21
5.3 COMMAND SUMMARY		22
5.4 COMMAND REFERENCE		23
5.4.1 CAUTO		23
5.4.2 CZERO		24
5.4.3 DACSTEP		25
5.4.4 O3		26
5.4.5 SETADDR		27
5.4.6 TDUMP		28
5.4.7 TLIST		29
5.4.8 VGET		30
5.4.9 VLIST		31
5.4.10 VSET		32
6.0 MAINTENANCE		33
6.1 REPLACING THE GAS FILTER ELEMENT (OPTIONAL)		33

P/N 03662D Teledyne API Model 460H O3 Monitor Operator Manual - Page iii

Image 3

Teledyne 460H Table Of Contents, I. 0 INTRODUCTION, Installation, Startup, Operation, Serial Communications, Maintenance

Contents

03662 Rev. D 1/8/04 MODEL 460H NEMA OZONE MONITORINSTRUCTION MANUAL EMAIL api-sales@teledyne.com SAFETY MESSAGES I. 0 INTRODUCTION TABLE OF CONTENTS2.0 INSTALLATION 6.0 MAINTENANCE 6.3 DEGREE OF PROTECTION 6.2 CLEANING EXTERIOR SURFACES OF THE M460H7.0 SENSOR AND SYSTEM TROUBLESHOOTING APPENDIX A - SERIAL PORT CONFIGURATION Electrical Connections FIGURESFigure 2-1 Mounting Hole Locations Pneumatic Connections Serial Port Configuration TABLESTable 2-1 Digital Status Output Pins Table 2-3 Serial Port Pins 1.1 Preface I.0 INTRODUCTION TERMS AND CONDITIONS 1.2 WARRANTY POLICYADVANCED POLLUTION INSTRUMENTATION DIVISION 02024c 1.3 Principle of Operation 1.4 Specifications 2.0 Installation 2.1 Mechanical InstallationFigure 2-1 Mounting Hole Locations Figure 2-2 Pneumatic Connections 2.2 Pneumatic Connections 2.3AC Power Connection I/O CONNECTOR 2.4 Electrical I/O Connections2.4.1 Analog Output Figure 2-3 Electrical Connections Name Table 2-1 Digital Status Output Pins2.4.2 Digital Status Outputs Label Description 2.4.3 Control InputsTable 2-2 Control Inputs Input RS232 Table 2-3 Serial Port Pins2.4.4 RS232/RS485 Serial Communications Port Figure 2-5 Typical RS232 and RS485 Connections 3.0 Startup 4.1.2 Pressure Display 4.0 Operation4.1 Front Panel Display 4.1.1 O3 readout 4.2.2 Auto-Zero Function 4.2.1 Auto-Zero Installation4.2.3 Auto Zero Error 4.2 Auto-Zero Operation addresscommanddata1,data2#checksumCR 5.1 Serial Port Configuration5.2 Command Syntax Table 5-1 Serial Port Configuration Table 5-2 Serial Port Command Summary 5.3 Command SummaryExamples of valid Commands with no data Examples of valid Commands with data Data Parameters Sent 5.4 Command Reference5.4.1 CAUTO Syntax 5.4.2 CZERO 5.4.3 DACSTEP 5.4.4 O3 addressO3CRaddresso3conc#checksumCR addressSETADDRnewaddressCR 5.4.5 SETADDR 5.4.6 TDUMP 5.4.7 TLIST addressvarvalue#checksumCR 5.4.8 VGETAllowable Range Index 5.4.9 VLIST 1VLISTCR#5 iirfilt = 0.4 #6 concunits = newvalue 5.4.10 VSETvarindex is index number for internal VAR See VGET for index list 6.1 Replacing the gas filter element 6.0 Maintenance6.2 Cleaning Exterior Surfaces of the M460H Filter Replacement Procedure Table 7-1 Digital Status Outputs 7.0 Sensor and System Troubleshooting7.1 Status Output Summary 7.2 Sensor OK 7.3 Invalid Reading 7.4 Lamp Low7.5 Cell Dirty Invalid 7.6 Status Output Summary TableTable 7-2 Status Output Truth Table Sensor Appendix A - Serial Port Configuration Figure A-1 RS232/RS485 Jumpers Controller PCA#03492RS232RS485 Appendix B - Pneumatic Diagram