Appendix B - Pneumatic Diagram | Teledyne 460H specs

Appendix B – Pneumatic Diagram

O3 Gas In
Filter		Flow Control		Flow-Meter
	Azero Valve	Orifice	O3	O3 Destruct
Zero Gas In	Azero Valve		O3	O3 Destruct
Zero Gas In			Measurement
			Measurement
			Cell
Exhaust Out

P/N 03662D Teledyne API Model 460H O3 Monitor Operator Manual - Page 38

Page 38

Image 38

Teledyne Appendix B - Pneumatic Diagram, P/N 03662D Teledyne API Model 460H O3 Monitor Operator Manual - Page

Contents

EMAIL api-sales@teledyne.com MODEL 460H NEMA OZONE MONITORINSTRUCTION MANUAL 03662 Rev. D 1/8/04 SAFETY MESSAGES 6.0 MAINTENANCE TABLE OF CONTENTS2.0 INSTALLATION I. 0 INTRODUCTION APPENDIX A - SERIAL PORT CONFIGURATION 6.2 CLEANING EXTERIOR SURFACES OF THE M460H7.0 SENSOR AND SYSTEM TROUBLESHOOTING 6.3 DEGREE OF PROTECTION Pneumatic Connections FIGURESFigure 2-1 Mounting Hole Locations Electrical Connections Table 2-3 Serial Port Pins TABLESTable 2-1 Digital Status Output Pins Serial Port Configuration I.0 INTRODUCTION 1.1 Preface 02024c 1.2 WARRANTY POLICYADVANCED POLLUTION INSTRUMENTATION DIVISION TERMS AND CONDITIONS 1.3 Principle of Operation 1.4 Specifications Figure 2-1 Mounting Hole Locations 2.0 Installation2.1 Mechanical Installation 2.2 Pneumatic Connections Figure 2-2 Pneumatic Connections 2.3AC Power Connection Figure 2-3 Electrical Connections 2.4 Electrical I/O Connections2.4.1 Analog Output I/O CONNECTOR Label Table 2-1 Digital Status Output Pins2.4.2 Digital Status Outputs Name Input 2.4.3 Control InputsTable 2-2 Control Inputs Description Figure 2-5 Typical RS232 and RS485 Connections Table 2-3 Serial Port Pins2.4.4 RS232/RS485 Serial Communications Port RS232 3.0 Startup 4.1.1 O3 readout 4.0 Operation4.1 Front Panel Display 4.1.2 Pressure Display 4.2 Auto-Zero Operation 4.2.1 Auto-Zero Installation4.2.3 Auto Zero Error 4.2.2 Auto-Zero Function Table 5-1 Serial Port Configuration 5.1 Serial Port Configuration5.2 Command Syntax addresscommanddata1,data2#checksumCR Examples of valid Commands with data 5.3 Command SummaryExamples of valid Commands with no data Table 5-2 Serial Port Command Summary Syntax 5.4 Command Reference5.4.1 CAUTO Data Parameters Sent 5.4.2 CZERO 5.4.3 DACSTEP addresso3conc#checksumCR 5.4.4 O3addressO3CR 5.4.5 SETADDR addressSETADDRnewaddressCR 5.4.6 TDUMP 5.4.7 TLIST Index 5.4.8 VGETAllowable Range addressvarvalue#checksumCR #5 iirfilt = 0.4 #6 concunits = 5.4.9 VLIST1VLISTCR is index number for internal VAR See VGET for index list 5.4.10 VSETvarindex newvalue Filter Replacement Procedure 6.0 Maintenance6.2 Cleaning Exterior Surfaces of the M460H 6.1 Replacing the gas filter element 7.2 Sensor OK 7.0 Sensor and System Troubleshooting7.1 Status Output Summary Table 7-1 Digital Status Outputs 7.5 Cell Dirty 7.3 Invalid Reading7.4 Lamp Low Sensor 7.6 Status Output Summary TableTable 7-2 Status Output Truth Table Invalid RS232RS485 Appendix A - Serial Port ConfigurationFigure A-1 RS232/RS485 Jumpers Controller PCA#03492 Appendix B - Pneumatic Diagram

Teledyne 460H instruction manual Appendix B - Pneumatic Diagram

Models: 460H

Appendix B – Pneumatic Diagram