Manuals
/
Thermo Products
/
Household Appliance
/
Burner
Thermo Products
chx-3 75n, 100n, 125n operation manual
Models:
125n
100n
chx-3 75n
1
66
67
67
Download
67 pages
17.21 Kb
60
61
62
63
64
65
66
67
<
>
Troubleshooting
Specification
The CHX3/CDX3 furnace models are sealed combustion design, which does not require an air shutter adjustment air shutters are not used for proper flame characteristics. Burner box access cover must always be secured with all screws in place and tightened before operating furnace
Install
Parts list
Appendix – B Wiring Diagrams
Connecting The Combustion Air Intake Piping
Diagnostic Features
I.Condensate Drain Line And Trap Assembly
Go to Checkout Procedure below
Page 66
Image 66
All installations and services must be performed by qualified service personnel.
60
Page 65
Page 67
Page 66
Image 66
Page 65
Page 67
Contents
CHX3-125N CDX3-125N
MODELS FOR USE WITH NATURAL GAS OR LP GAS PROPANE
CHX3-75N CDX3-75N CHX3-100N CDX3-100N
INSTALLATION AND OPERATION MANUAL
I. SAFETY INFORMATION
This and the previous page contain reproductions of the various warning and instruction labels placed on the Thermo Pride Two Stage Condensing Gas Furnaces. Please read and comply with the contents of these labels
1.A windows be opened
The CHX3/CDX3 furnace models are sealed combustion design, which does not require an air shutter adjustment air shutters are not used for proper flame characteristics. Burner box access cover must always be secured with all screws in place and tightened before operating furnace
INDEX
SECTION
BEGINNING PAGE
II. FURNACE SPECIFICATIONS
CDX3 SERIES
INSTALLATION PARTS PACKAGES – CHX3-75
INSTALLATION PARTS PACKAGES – CDX3-75
Grounding instructions
III. GENERAL INSTALLATION
B. FURNACE LOCATION
B1. CDX3 HORIZONTAL APPLICATION
Figure
PVC Pipe Designation
Maximum Quantity of Elbows
E.Direct Venting Through a Sidewall
Outside Combustion Air Intake RH view
c.The vent terminal shall not be located
•near soffit vents, crawl space vents, or other areas where condensate or water vapor could create a nuisance, hazard, or cause property damage, and
Page
E1. Single-PipeSidewall Venting Option
5.Optional Direct Vent Terminations
Install these optional kits according to the instructions provided with each kit. The location and clearance requirements are identical to those of the standard vent terminations described in this manual
1.Figures 6B, 7, and 8 follow depicting typical exhaust vent and air intake connections for the furnace model series CHX3 and the CDX3, respectively, as well as a list of required parts to correctly install each system
Applications
Applications
leading away from the furnace must be composed of 3-inchdiameter PVC pipe and pipe fittings only. Refer to item E in Figure
3. Connecting The Combustion Air Intake Piping
I.CONDENSATE DRAIN LINE AND TRAP ASSEMBLY
Figure 14. TRAP ASSEMBLY MOUNTED ON CHX3
Figure 15. TRAP ASSEMBLY MOUNTED ON CDX3
2.Determine on which side of furnace the condensate disposal line is to be run NOTICE: On CHX3/CDX3’s this must be the same side as the flue outlet or bottom of unit. Attach the condensate trap to the furnace casing using the #8x3/4” sheet metal screws provided in the parts package. Pilot holes are provided on both sides of the casing for mounting
J. GENERAL GAS PIPING
Figure
J1. REQUIREMENTS AND SIZING OF DUCT WORK
Figure 18A
TABLE 2A
K. FILTERS 1. CHX3 MODELS: HIGHBOYS
Figure
2. CDX3 MODELS: COUNTERFLOWS
Figure
L. WIRING
Table 4A
Options
S7 DIP Switch
Switch Settings
Time
2-StageBlower Settings from factory Table 4C
IV. STARTING THE UNIT A. SEQUENCE OF OPERATIONS
FLAME MUST BE DETECTED
IF THERMOSTAT W2 CONTACTS ARE CLOSED OTHERWISE
B. INITIAL START UP
OPERATING INSTRUCTIONS
A.Burner manifold pressure with a pressure gauge
C. Measuring And Adjusting Heat Input Rate
Observe the following precautions when measuring
B.Gas flowrate by clocking gas meter
NOTICE: A U-tubemanometer, measuring pressure in inches of water column, is recommended for all gas pressure measurements. However, an aneroid pressure gauge, in good working condition, capable of reading pressure changes of 0.05 in. W.G., or less, that was recently calibrated within the last year, is a satisfactory alternate. These two 2 devices will be considered as equivalent and interchangeable. Either device is referred to below as a “pressure gauge”
Heat input rate in BTUH =
Figure
21.Go to Checkout Procedure below
Checking The Burner Flame
Checkout Procedure
TABLE 6 - CONVERTING GAS FLOW RATE
D. FURNACE CHECKOUT PROCEDURE
V. INSTALLERS INSTRUCTIONS TO USER
Figure VI. TROUBLESHOOTING
DIAGNOSTIC FEATURES
Power must be disconnected before servicing
TROUBLESHOOTING GUIDE
IS INDUCER RUNNING ON LOW SPEED? YES DOES THE HOT
DO BURNERS STAY LIT PAST PROOF OF FLAME CHECK?
REPLACE THE 50V51-843CONTROL
CHECK FOR 24 VOLTS
Appendix –AReplacement Parts List
Page
Page
Page
Appendix – B Wiring Diagrams
