Toshiba D-R160SB 1 2, 3

Introduction

Recording Playback Editing

Introduction Connections Basic Setup Function Setup Others

19EN

Installing batteries in the remote

control

About the remote control

Preparation of the remote control

■ Install two R6 (AA) batteries (supplied) into the

remote control, carefully match with the

polarity indicated inside the battery

compartment.

1Open the cover.

2 Insert batteries.

Make sure to match the + and - on the

batteries to the marks inside the battery

compartment.

3 Close the cover.

■ Keep in mind the following when using the

remote control:

● Make sure there is no obstacle between the remote

control and the remote control sensor on the unit.

● Use within the operating range and angle as

shown.

● Remote control operation may become unreliable if

the remote control sensor of the unit is being

exposed by the strong sunlight or fluorescent light.

● Remote controls for different devices can interfere

with each other. Be careful when using remote

controls for other equipment located close to the

unit.

● Replace the batteries when the operating range of

the remote control reduces.

● The maximum operable range as follows:

- Line of sight:

approximately 7 m

- Either side of the centre:

approximately 7 m within 30 degrees

REC MODE

REC

PROGRAM

ON/STANDBY

I

/

y

Notes:

• Incorrect use of batteries can result in hazards such as

leakage and bursting.

• Do not mix new and old batteries together.

• Do not use different kinds of batteries together.

• Make sure that the + and - ends of each battery match the

indications inside the battery compartment.

• Remove batteries if the remote control will not be used for

an extended period of time.

• When disposing used batteries, please comply with

governmental regulations or the public instructions for

environmental protection that apply in your country or

area.

• Do not recharge, short-circuit, heat, burn or disassemble

batteries.

Contents

Main D-R160SB D-R160SB Precautions CAUTION: CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Laser Safety Power Supply Declaration of Conformity Connection to Power Mains Cord Important Precautions (contd) Installation Location For safety and optimum performance of this unit: Avoid the Hazards of Electrical Shock and Fire Moisture Condensation Warning About Copyright Maintenance Table of contents Introduction Connections Basic Setup Recording Playback Editing Function Setup Others Features Recording Playback Editing Compatibility Choosing a disc For recording /playback Using different disc types for different purposes DVD disc types For playback only On DVD-R discs L On DVD-RW discs B Marks on DVD video discs 3 12 EN Choosing a disc (contd) Yes No Structure of disc contents Discs and purposes 14 EN Index to parts and controls 15 8*9 1211 101314 123*4567 12 4 53 6 7 8 9 10 11 Rear Panel Page Page Index to parts and controls (contd) Front Panel Display Guide Display message Installing batteries in the remote control About the remote control Preparation of the remote control 1 2 3 Keep in mind the following when using the remote control: Display menu On Screen menu Setup menus 63 14 5 252 3 Page Page Page Connections Connections Recording from a DVD player, VCR or other Audio-Video equipment with a Scart output jack (AV2) Recording from a camcorder or other Audio- Video equipment with no Scart output jack (AV3 or AV4) Using the S-VIDEO OUT or the COMPONENT VIDEO OUTPUT jacks and the ANALOG AUDIO OUT jacks Connecting to external equipment Connections Connections (contd) Digital audio for better sound quality The connections illustrated below are optional for better sound. Connecting a Dolby DigitalTM decoder, DTS decoder or MPEG decoder Connecting to an MD deck or DAT deck After you have completed connections Page Initial setting Channel setting Auto tuning Manual tuning To select a channel To skip a Preset channel Move Setting the clock Auto Clock Setting Manual Clock Setting Page Selecting the TV aspect ratio Page Recording Symbols in this Section Information on DVD recording Information Recording Mode Information on copy control Restrictions on recording Making discs playable in other DVD player (Finalise) Selecting the Recording format Choosing the recording format of a blank disc 1 2 Disc menu will appear. 3 <e.g. VR mode> Format menu will appear. 4 5 8 6 7 Reformatting a disc Setting Auto Chapter Recording Audio Select (XP) Selecting the Sound mode Setting External Input Audio Setting Bilingual Recording Audio Page Basic recording (contd) 6 [PROG. /] or [the Number buttons]. 8 7 The I mark will be displayed for 5 seconds. 1 2 3 One-touch Timer Recording (contd) 4 recording time (30 minutes to 8 hours) appears on the TV screen. 1:00 0:30 (Normal Recording) 8:00 7:30 Wait for a moment. will appear and this operation may take awhile to be completed. 1 In stop mode, press [TIMER PROG.]. 2 3 <e.g. 1st January> 31/01(one month later minus one day) Daily (Everyday) [K / L], then press [B]. 5 [K / L], then press [B]. (Continued) 7 6 8 is entered. 9 Checking, cancelling, or correcting the timer programming information * 5) Press [TIMER PROG.] to exit. 6) Press [I/y ON/STANDBY] to return to the timer standby mode. If the timer programming did not complete correctly PDC (Programme Delivery Control) Hints for Timer Recording The priority of overlapped settings If the starting time is same: If programming has been made at the end of the programming (PROG. 1) currently being recorded: Satellite Link 4) With start time and the recording mode highlighted, press [ENTER]. 5) Set the desired start time using [K / L / { / B]. 6) Select the desired recording mode using [K / L], then press [ENTER]. 7) With To Standby Mode highlighted, press [ENTER] again. Settings for an external equipment 1 2 3 5 4 Recording from an external equipment 1 2 65 2, 3 48 3 4 Page Setting disc protection 1 2 4 3 Finalising discs 1 2 3 Finalising discs (contd) 4 Finalise will start. 5 This operation may take awhile to be completed. Auto finalise 1 2 3 5 4 Page Symbols in this Section Playback Page 5 Playback 6 Basic playback (contd) 8 7 then press [ENTER].