Manuals / Toshiba / Computer Equipment / Webcam

Toshiba IK-TF5C instruction manual Specifications

Models: IK-TF5C

1 36

Download 36 pages 20.96 Kb

Page 34

10. SPECIFICATIONS

10. SPECIFICATIONS

Power supply	DC12V±10%
Power consumption	Approx. 4.3W
Pick-up system	RGB, 3CCD
Image sensor	1/3inch All pixels CCD
(Effective pixels)	(Horizontal : 659pixels, Vertical : 494pixels)
Scanning system	Progressive scan
Scan frequency	Horizontal : 31.469kHz, Vertical : 59.94Hz
Sync system	Internal/External (Automatic switching)
Horizontal resolution	500TV lines
Sensitivity	F6.8 standard (2000 lx, 3000K)
Minimum illumination	14 lx (F2.2, Sensitivity + 18 dB, 3000K)
Lens mount	C mount (flange back : 17.526 mm in-air)
Ambient temperature	32 to 104°F (0 to 40°C)
Ambient humidity	Less than 90%
Weight	Approx. 5.82oz (165g)
External dimension	1.73” (W) x 1.73” (H) x 3.07” (D)
	(44 (W) x 44 (H) x 78 (D) mm)	(except for protruded portion)
White balance	AWB (Automatic white balance), MANUAL (Manual)
Gain	MANUAL (Manual), OFF (0 dB)
Output signal	8-bit RGB, Digital output (Camera Link format)
Sync signal output	FVAL, LVAL, DVAL (Positive polarity)
	Pixel Clock (24.5454MHz)
External sync input	HD or VD : Negative
Interface	Serial data interface : Ser TC (RXD), Ser TFG (TXD)
Optional parts	EXC-CL05S (Cable), etc

The designs and specifications are subject to change without notice.

34

Image 34

Toshiba IK-TF5C instruction manual Specifications, The designs and specifications are subject to change without notice

Contents

Following information is only for EU-member states For Customer UseFCC NOTICE IK-TF5CAvoid installing in a shower room or a bathroom SAFETY PRECAUTIONSStop operation immediately when any abnormality or defect occurs Use the specified power supplyAvoid setting in humid, smoky, vaporized or dusty places Note the following instructions when installingDo not put the product in direct sunshine and/or high temperature Disclaimer3. ITEMS CONTROLLED BY USING TABLE OF CONTENTS6. OPERATION 1. CAUTIONS ON USE AND INSTALLATION 2. COMPONENTS3. ITEMS CONTROLLED BY USING ON SCREEN DISPLAY Available selections4. NAMES AND FUNCTIONS AWB DISP MENU DATA DC IN PAGE5. 1 Standard Connection 5. 3 Connector Pin Assignments5. CONNECTION 5. 2 Cautions on Connection6. OPERATION 6. 1 White Balance6. 2 Gain 6. 3 Shading Correction7. MODE SETTING BY ON SCREEN DISPLAY 7. 1 Using the Menus7. 2 Menus 1 SHUTTER Electronic shutter1. 2 Changing each setting in SS synchro. scan mode a Changing the polarity of inputting trigger pulse setting 1. 3 Changing each setting in E.TRG mode1. 3. 1 Changing each setting in 1P SNR mode b Changing 1P SNR exposure time settingb Changing 1P SR exposure time setting 1. 3. 2 Changing each setting in 1P SR modea Changing the polarity of inputting trigger pulse setting c Changing the partial scanning setting1. 3. 3 Changing each setting in PW SNR mode 1. 3. 4 Changing each setting in PW SR mode a Changing the partial scanning setting 2 GAIN Video gain1. 3. 5 Changing each setting in RR mode 2. 1 Changing each setting in GAINa Changing color temperature setting 3 WHT BAL White balance3. 1 Changing each setting in AWB Automatic White Balance mode 3. 2 Changing each setting in MANU Manual mode4. 5 Changing the manual shading correction setting 4 PROCESS4. 4 Changing the shading correction mode 4. 1 Changing master pedestal5. 1 Adjusting horizontal phase 5 SYNC6 OPTION 6. 1 Changing serial communication baud rate7. 3 External Sync 7 Setting to factory setting status1 External sync signal polarity 2 External sync frequency range1 Setting by 1H 2 Setting by the frame3 Using the unit with external sync signal 7. 4 Synchro. Scan Operation1 1P SNR 1 Pulse Trigger Sync Non Reset 7. 5 EXT TRIG External triggerNegative polarity mode Trigger*1 Positive polarity mode About 1 ∝s 2 1P SR 1 Pulse Trigger Sync Reset 2. 1 1 Pulse Trigger SYNC-RESET Picture Output Timing3 PW SNR Pulse width trigger SYNC-NON RESET Negative polarity mode Trigger*1 Positive polarity mode 4 PW SR Pulse width trigger SYNC-RESET 4. 1 1 Pulse Width Trigger SYNC-RESET Picture Output Timing5. 2 Input Timing Chart Example 5 RR Reset restart5. 1 Long Term Exposure 1 Partial Scanning OFF All pixels scanning 3 When Partial Scanning Mode is ON7. 6 Partial Read 2 Partial Scanning ON3 Trigger Pulse Specifications 8. INPUT OUTPUT SIGNAL SPECIFICATOINS1 HD Input Specifications 6 External HD/VD Input Phase Specifications1 Horizontal Output Waveform Timing Chart 9. CCD OUTPUT WAVEFORM TIMING CHART2 Vertical Output Waveform Timing Chart 10. SPECIFICATIONS The designs and specifications are subject to change without noticeSymptom 11. EXTERNAL APPEARANCE DIAGRAM12. BEFORE MAKING A SERVICE CALL Items to be checkedLIMITED WARRANTY TOSHIBA CCD CAMERA