Manuals / TP-Link / Computer Equipment / Network Router

TP-Link TL-R480T+ manual  Dynamic IP Status

Models: TL-R480T+

1 131

Download 131 pages 54.17 Kb

Page 28

Get IP Address by	The broadcast requirement may not be supported by a few ISPs.
Unicast:	Select this option if you can not get the IP address from your ISP
	even with a normal network connection. This option is not required
	generally.
Use the following DNS	Select this option to enter the DNS (Domain Name Server) address
Server:	manually.
Primary DNS:	Enter the IP address of your ISP’s Primary DNS (Domain Name
	Server). If you are not clear, please consult your ISP.
Secondary DNS:	Optional. If a Secondary DNS Server address is available, enter it.
Upstream Bandwidth:	Specify the bandwidth for transmitting packets on the port.
Downstream	Specify the bandwidth for receiving packets on the port.
Bandwidth:
 Dynamic IP Status
Status:	Displays the status of obtaining an IP address from your ISP.
	 “Disabled” indicates that the Dynamic IP connection type is not
	applied.
	 “Connecting” indicates that the router is obtaining the IP
	parameters from your ISP.
	 “Connected” indicates that the router has successfully obtained
	the IP parameters from your ISP.
	 “Disconnected” indicates that the IP address has been
	manually released or the router gets no response from your
	ISP. Please check your network connection and consult your
	ISP if this problem remains.
IP Address:	Displays the IP address assigned by your ISP.
Subnet Mask:	Displays the Subnet Mask assigned by your ISP.
Gateway Address:	Displays the Gateway Address assigned by your ISP.
	-22-

Image 28

TP-Link TL-R480T+ manual  Dynamic IP Status, Select this option to enter the DNS Domain Name Server address

Contents

TL-R480T+ Load Balance Broadband Router REV6.2.0 1910011011FCC STATEMENT COPYRIGHT & TRADEMARKSCE Mark Warning Safety Information 安全諮詢及注意事項CONTENTS Chapter 3 Quick Installation GuideChapter 4 Configuration Chapter 1 About this GuideAppendix A Hardware SpecificationsAppendix B Glossary Appendix CPackage Contents Symbol Chapter 1 About this Guide1.1 Intended Readers 1.2 ConventionsAppendix B FAQ Provides the possible solutions to the problems that may occurduring the installation and operation of the router Appendix C Glossary Powerful Data Processing Capability  Powerful FirewallChapter 2 Introduction 2.1 Overview of the Router2.2 Features  Easy-to-useHardware Basic Functions2.3 Appearance 2.3.1 Front PanelTraffic Control Security Reset button  AC Power Receptacle2.3.2 Rear Panel  Interface DescriptionChapter 3 Quick Installation Guide 3.1 Configure PCPage Page Is the TCP/IP configuration for your PC correct? 3.2 LoginIs the connection between your PC and the router correct? Figure 3-8 Quick Setup Figure 3-9 WAN ModeFigure 3-10 WAN Port Figure 3-11 WAN Connection TypeFigure 3-13 WAN Connection Type - PPPoE Connecting Figure 3-12 WAN Connection Type - PPPoEFigure 3-15 WAN Connection Type - Static IP Figure 3-14 WAN Connection Type - Dynamic IPIf you have difficulty in this process, please contact your ISP Figure 3-16 WAN Connection Type - Static IP Connecting Figure 3-17 Configuration CompletedChapter 4 Configuration 4.1 Status4.2 Quick Setup 4.3.1.1 WAN Mode WAN Mode 4.3 Network1 Static IP  Static IPChoose the menu Network→WAN→WAN1 to load the configuration page Tips2 Dynamic IP Default GatewayPrimary DNS Secondary DNS Dynamic IP  Dynamic IP Status Select this option to enter the DNS Domain Name Server address3 PPPoE Primary DNS Displays the IP address of your ISP’s Primary DNSSecondary DNS Displays the IP address of your ISP’s Secondary DNS Figure 4-5 WAN - PPPoE PPPoE Settings on. The connection can be re-established automatically when it576-1492. The default MTU is 1480. You are recommended to keep Enter the Account Name provided by your ISP. If you are not clearHere allows you to configure the secondary connection. Dynamic IP Dynamic IP is selected, the obtained subnet address of WAN port is PPPoE Status manually terminated or the router gets no response from4 L2TP Figure 4-6 WAN - L2TP L2TP Settings Enter the Account Name provided by your ISP. If you are not L2TP Status Default GatewayIP Address Subnet Mask5 PPTP Displays the IP address of your ISP’s Secondary DNS PPTP Settings PasswordActive Mode Connection Type PPTP Status Default GatewaySubnet Mask Upstream Bandwidth BigPond Settings 6 BigPondAuth ModeYou can select the proper Active mode according to your need the address of Auth Server is a server name4.3.2.1 LAN 4.3.2 LAN BigPond Status 4.3.2.2 DHCP  LAN DHCP Settings 4.3.2.3 DHCP Client4.3.2.4 DHCP Reservation  DHCP Reservation List of Reserved Address 4.3.3 IPTV IGMP 4.3.4 MAC Address Set the MAC Address for LAN portSet the MAC Address for WAN port Tips4.3.5.1 Statistics 4.3.5 Switch MAC Address  Statistics 4.3.5.2 Port Mirror  General Port Mirror ModeMirroring Port Mirrored Port4.3.5.3 Rate Control Application Example Port Config 4.3.5.4 Port Config Rate Control 4.3.5.5 Port Status 4.3.5.6 Port VLAN4.4 User Group 4.4.1 Group Port VLAN Tips Group Config  User Config4.4.2 User 4.4.3 View View Config View4.5.1.1 NAT Setup 4.5 Advanced4.5.1 NAT  NAPT One-to-One NAT 4.5.1.2 One-to-One NAT List of Rules  Multi-Nets NAT 4.5.1.3 Multi-Nets NAT list of Rules Application Example  Network Requirements  Configuration procedure 4.5.1.4 Virtual Server  Virtual Server4.5.1.5 Port Triggering  List of Rules Port Triggering Status4.5.1.6 ALG  ALG List of Rules FTP ALG4.5.2.1 Setup 4.5.2 Traffic Control Interface Bandwidth upper limit configured here. Value 0 means all the remained bandwidth4.5.2.2 Bandwidth Control  Bandwidth Control Rule4.5.3.1 Session Limit 4.5.3 Session Limit List of Rules  Session Limit 4.5.3.2 Session List List of Session Limit 4.5.4 Load Balance 4.5.4.1 Configuration4.5.4.2 Policy Routing  General Select the WAN port for transmitting packets4.5.4.3 Link Backup  List of Rules General 4.5.4.4 Protocol  List of Rules4.5.5 Routing 4.5.5.1 Static Route Protocol  List of Protocol Static Route  List of Rules Configuration procedure Application Example  Network Requirements4.6.1 Anti ARP Spoofing 4.6 Firewall4.6.1.1 IP-MAC Binding  IP-MAC Binding  GeneralIP Address Status4.6.1.2 ARP Scanning  List of Rules4.6.2 Attack Defense 4.6.1.3 ARP ListFlood attack is a kind of commonly used DoS Denial of Service the corresponding thresholds. Keep the default settings if you are General Flood Defense4.6.3 MAC Filtering  MAC FilteringEnable Attack Defense Logs4.6.4 Access Control 4.6.4.1 URL Filtering List of Rules  General Configuration Procedure  URL Filtering Rule List of Rules Application Example  Network Requirements4.6.4.3 Access Rules 4.6.4.2 Web Filtering Access Rules  List of Rules 4.6.4.4 Service  Service List of Service 4.6.5 App Control4.6.5.1 Control Rules  General Control Rules 4.6.5.2 Database List of Rules 4.7 Services 4.7.1 PPPoE Server4.7.1.1 General  GeneralDNS0.0.0.0  MS-CHAP v2 with a higher security is an improved version of MS-CHAP4.7.1.2 IP Address Pool 4.7.1.3 Account IP Address Pool  List of IP PoolPassword IP Address Assigned Mode Static IP Address IP Address Pool  Account Account NameMax Sessions Expiration Date 4.7.1.4 Exceptional IP is 48. If Enable Advanced Account Features is not selected, the List of Account  Exceptional IP 4.7.1.5 List of Account List of Exceptional IP  General 4.7.2 E-BulletinInterval 4.7.3 Dynamic DNS  E-Bulletin List of E-Bulletin Tips4.7.3.1 DynDNS  Dyndns DDNS 4.7.3.2 No-IP List of DynDNS Account  No-IP DDNS 4.7.3.3 PeanutHull  List of No-IP Account PeanutHull DDNS 4.7.3.4 Comexe List of PeanutHull Account  Comexe DDNS 4.7.4 UPnP  List of Comexe Account List of UPnP Mapping  General4.8 Maintenance 4.8.1 Admin Setup4.8.1.1 Administrator  Administrator4.8.1.2 Login Parameter  General Configuration Procedure 4.8.1.3 Remote ManagementApplication Example  Network Requirements 4.8.2.1 Factory Defaults 4.8.2 Management4.8.2.2 Export and Import  Remote Management4.8.2.3 Reboot  Configuration Version Export  Import4.8.2.4 Firmware Upgrade 4.8.3 SNMPChoose the menu Maintenance→SNMP→SNMP to load the following page  General4.8.4 Statistics 4.8.4.1 Interface Traffic Statistics4.8.4.2 IP Traffic Statistics  Interface Traffic Statistics4.8.5 Diagnostics 4.8.5.1 Diagnostics Traffic Statistics  IP Traffic Statistics Ping  Tracert 4.8.5.2 Online Detection General 4.8.6 Time 4.8.6.1 Time List of WAN status  Current Time Config 4.8.6.2 Daylight Saving Time4.8.7 Logs  Daylight Saving TimeDST Config Daylight Saving TimeDST State Show the work state of DST  List of Logs Level Config Severity Filter Setting 4.8.8 NAT Tabledebugging  NAT TableAging Time Displays the time which the link lasts Unit second Out LinkDisplays the WAN port which is used in the linkAppendix A Hardware Specifications PowerPorts Transmission MediumAppendix B FAQ 4. Make sure that the NAT DMZ service is disabled Glossary Appendix C GlossaryDescription Glossary for services such as IPSec that require keys. Before any IPSecDescription Glossary DescriptionDescription GlossaryTelnet is used for remote terminal connection, enabling users to