Mstp Instance, Region Config, Instance Config | TP-Link TL-SG2008

	z Disconnected: In this status the port is not participating in the
	STP.
LAG:	Displays the LAG number which the port belongs to.

Note:

1.Configure the ports connected directly to terminals as edge ports and enable the BPDU protection function as well. This not only enables these ports to transit to forwarding state rapidly but also secures your network.

2.All the links of ports in a LAG can be configured as point-to-point links.

3.When the link of a port is configured as a point-to-point link, the spanning tree instances owning this port are configured as point-to-point links. If the physical link of a port is not a point-to-point link and you forcibly configure the link as a point-to-point link, temporary loops may be incurred.

7.3 MSTP Instance

MSTP combines VLANs and spanning tree together via VLAN-to-instance mapping table (VLAN-to-spanning-tree mapping). By adding MSTP instances, it binds several VLANs to an instance to realize the load balance based on instances.

Only when the switches have the same MST region name, MST region revision and VLAN-to-Instance mapping table, the switches can be regarded as in the same MST region.

The MSTP Instance function can be implemented on Region Config, Instance Config and Instance Port Config pages.

7.3.1 Region Config

On this page you can configure the name and revision of the MST region

Choose the menu Spanning Tree→MSTP Instance→Region Config to load the following page.

Figure 7-7 Region Config

The following entries are displayed on this screen:

¾Region Config

Region Name: Create a name for MST region identification using up to 32 characters.

Revision:Enter the revision from 0 to 65535 for MST region identification.

7.3.2 Instance Config

Instance Configuration, a property of MST region, is used to describe the VLAN to Instance mapping configuration. You can assign VLAN to different instances appropriate to your needs. Every instance is a VLAN group independent of other instances and CIST.

Choose the menu Spanning Tree→MSTP Instance→Instance Config to load the following page.

66

Image 73

TP-Link TL-SG2008 manual Mstp Instance, Instance Config, ¾ Region Config

Contents

REV1.0.0 1910010984 TL-SG2008 Copyright & Trademarks FCC Statement Safety Information Contents Loopback Detection 100 Rmon Package Contents Intended Readers About this GuideConventions Overview of This Guide System Chapter Introduction Appendix a Specifications Main Features Overview of the SwitchIntroduction Appearance Description ¾ LEDs Name Status Indication Rear Panel Login Login to the SwitchConfiguration Return to Contents System Info SystemSystem Summary ¾ Port Status ¾ Port Info Device DescriptionStatus Displays the connection status of the port ¾ Bandwidth Utilization ¾ Device Description System Time¾ Time Info Daylight Saving Time System IP Following entries are displayed on this screen System IP User Management ¾ IP ConfigUser Table Password Type in a password for users’ login User Config¾ User Info User Status Confirm Password Password Display Mode Config RestoreUser ID, Name, Access Level and status Operation System Tools Firmware Upgrade Config Backup¾ Config Backup System Reset System Reboot Access Control Access Security IP Address & Mask SSL ConfigMAC Address Port ¾ Certificate Download ¾ Global Config¾ Key Download Key File Select Enable/Disable SSH function SSH Config Download ¾ Configuration Procedure¾ Network Requirements Application Example 2 for SSH Page Page Return to Contents Port Config SwitchingPort Group Port MirrorMirroring Mode Ingress NumberEgress ¾ Port Security Port Security Port Isolation Port Isolation Loopback Detection ¾ Port Isolation Config¾ Port Isolation List Forward Portlist Display the forwardlist LAG Operation Mode ¾ LAG Table LAG Table Group Number Static LAGMember LAG will delete this LAG Lacp Config Admin Key ¾ Lacp ConfigPort Priority Traffic Summary Traffic MonitorPackets Rx Packets Tx Refresh Rate Traffic Statistics¾ Statistics Received Bound MAC address MAC AddressWay Port ¾ Search Option Address Table Static Address MAC Address Displays the MAC address learned by the switch¾ Address Table Displays the corresponding Vlan ID of the MAC address ¾ Static Address Table Dynamic Address ¾ Dynamic Address Table ¾ Aging ConfigBind ¾ Create Filtering Address Filtering Address ¾ Filtering Address Table Dhcp Filtering¾ Dhcp Working Principle 17 Network diagram of Dhcp ¾ Dhcp Cheating Attack 19 Dhcp Cheating Attack Implementation Procedure Dhcp Filtering ¾ Dhcp Filtering¾ Trusted Port Vlan ¾ Link Types of ports 802.1Q Vlan ¾ Pvid Vlan Config Name Give a name to the Vlan for identificationUntagged Ports Tagged Ports Application Example for 802.1Q Vlan ¾ Network DiagramUntagged Tagged Required. On VLAN→802.1Q VLAN→VLAN Config page, create a Required. On VLAN→802.1Q VLAN→VLAN Config page, configureStep Operation Description ¾ STP Elements Spanning Tree ¾ Bpdu Comparing Principle in STP mode ¾ STP Timers¾ STP Generation Tips ： Step Operation ¾ Mstp Elements ¾ Rstp Elements ¾ Port Roles ¾ Port States STP Config STP Config Version Forward DelayHello Time Max Age STP Summary Port Config ExtPath PriorityIntPath Edge Port Instance Config Region Config¾ Region Config Mstp Instance Instance ¾ Instance TableClear ¾ VLAN-Instance Mapping Instance ID Instance Port ConfigPath Cost Port Protect STP Security ¾ TC Protect ¾ Root Protect¾ Bpdu Protect ¾ Bpdu Filter TC Protect 11 TC Protect Application Example for STP Function On Spanning Tree→MSTP Instance→Region On Spanning Tree→STP Config→STP ConfigOn Spanning Tree→MSTP Instance→Instance Operation Description On Spanning Tree→STP Config→Port Config ¾ Suggestion for Configuration ¾ Multicast Overview Multicast ¾ Multicast Address Table ¾ Multicast Address Multicast IP Port Igmp Snooping¾ Igmp Snooping ¾ Igmp Snooping Process ¾ Igmp Snooping Fundamentals Snooping Config Description Displays Igmp Snooping status Member ¾ Igmp Snooping Status Fast Leave Igmp Snooping Multicast Vlan ¾ Multicast Vlan Vlan On the Multicast→IGMP Snooping→Snooping ConfigMulticast→IGMP Snooping→Multicast Vlan Snooping→Snooping Config Snooping→Port ConfigMulticast IP Multicast IP Table Static Multicast IP ¾ Create Static Multicast Multicast Filter¾ Static Multicast IP Table Port Filter IP-Range Action Mode ¾ Port Filter ConfigFilter Bound IP-Range ID Packet Statistics Port Displays the port number of the switch Query PacketMulticast→Multicast Filter→IP-Range Multicast→Multicast Filter→Port Filter Return to Contents QoS ¾ Priority Mode¾ QoS 802.1Q frame ¾ Schedule Mode SP-Mode DiffServ ¾ Port Priority ConfigPort Priority Displays the LAG number which the port belongs to 2 802.1P/CoS Mapping ¾ 802.1P Priority ConfigRequired. On QoS→DiffServ→Port Priority ¾ Priority Level ¾ Dscp Priority Config Configuration Procedure Step Operation DescriptionDscp Priority Mapping ¾ Priority Level Schedule ModeIt ranges from 0 to Priority Level Bandwidth Control ¾ Rate Limit ConfigRate Limit Ingress Rate bps Storm ControlEgress Ratebps Broadcast Rate Voice VlanBps Mulitcast Rate ¾ Port Voice Vlan Mode ¾ Security Mode of Voice Vlan Global ConfigPacket Type Processing Mode Enter the Vlan ID of the voice Vlan Port ModeAging Time OUI address is aging out OUI Config Optional. On QoS→Voice VLAN→OUI Config page, you Required. On VLAN→802.1Q VLAN→VLAN ConfigRequired. On QoS→Voice VLAN→Port Config Required. On QoS→Voice VLAN→Global Config ACL ACL ConfigACL Summary ACL Create ¾ Create ACL MAC ACL¾ Create MAC ACL Rule ID Extend-IP ACL Standard-IP ACL¾ Create Standard-IP ACL Mask Policy Summary Policy Config¾ Create Extend-IP ACL IP Protocol Action Create Policy CreateIndex Displays the index of the policy Displays the ID of the ACL contained in the policy Binding Table Policy Binding¾ Create Action ¾ Policy Bind Table Vlan Binding Port BindingInterface Direction Displays the binding direction Application Example for ACL ¾ VLAN-Bind ConfigEnter the ID of the Vlan you want to bind ¾ VLAN-Bind Table On ACL→ACL Config→Standard-IP ACL page, select ACL On ACL→ACL Config→ACL Create page, create ACL Limit2 ¾ Snmp Overview Snmp¾ Snmp Management Frame ¾ Snmp Versions ¾ MIB Introduction ¾ Snmp Configuration Outline Snmp Config, Notification and Rmon Snmp Config Snmp Group Snmp ViewMIB Object ID View Type Snmp Group Following entries are displayed on this screen ¾ Group Config ¾ Group Table Snmp User Auth Password Auth ModePrivacy Mode Privacy Password Snmp Community AccessCommunity Name MIB View Required. On the SNMP→SNMP Config→SNMP Required. On the SNMP→SNMP Config→GlobalConfig→Global Config page, enable Snmp On the SNMP→SNMP Config→SNMP ¾ Create Notification NotificationIP Address UDP Port Rmon TimeoutRetry ¾ Notification Table Rmon Group Function History Control¾ History Control Table Alarm Config Event Config¾ Event Table Sample Type VariableRising Threshold Rising Event 131 System Monitor MaintenanceCPU Monitor Memory Monitor 12.2 LogLevel Description Level Description Debugging Log Table¾ Log Info Time Local Log ¾ Local Log ConfigLog Buffer Log File Remote Log Backup Log¾ Log Host Host IP ¾ Backup Log Device DiagnosticsCable Test ¾ Cable Test Loopback Network Diagnostics Ping ¾ Ping ConfigTracert 10 Tracert Following entries are displayed on this screen ¾ Tracert Config Appendix a Specifications Configure TCP/IP component Appendix B Configuring the PCs Now Appendix C Glossary Remote Authentication Dial-in User Service Radius Multicast SwitchingIgmp Snooping Igmp Query Simple Network Management Protocol Snmp Rapid Spanning Tree Protocol RstpSimple Network Time Protocol Sntp Spanning Tree Algorithm STA