Quick Setup, 4.3 QSS | TP-Link TL-WA730RE manual

4.2 Quick Setup

TL-WA730RE150Mbps Wireless Range Extender User Guide

¾Firmware Version - This field displays the current firmware version of the AP.

¾Hardware Version - This field displays the current hardware version of the AP

¾Wired - This field displays the current settings or information for the Network, including the MAC address, IP address and Subnet Mask.

¾Wireless - This field displays basic information or status for wireless function, including

Wireless Mode, SSID, Channel, Mode, Channel Width, Max Tx Rate and MAC Address.

¾Traffic Statistics - This field displays the AP's traffic statistics.

¾System Up Time - This filed displays the run time of the AP since it’s powered on or reset.

)Note:

If you select Access Point mode in Figure 3-10,the wireless status in Figure 4-1will change, similar to the figure below:

4.2 Quick Setup

Please refer to Section 3.2: "Quick Installation Guide."

4.3QSS

QSS (Quick Secure Setup) can help you to quickly and securely connect to a network. This section will guide you to add a new wireless device to an existing network quickly by function. The QSS function is only available when the Operation Mode is set to Access Point. Select menu “QSS”, you will see the next screen shown in Figure 4-2.

18

Image 25

TP-Link manual Quick Setup, 4.3 QSS, TL-WA730RE 150Mbps Wireless Range Extender User Guide

Contents

Rev 1.0.0 TL-WA730RE 150Mbps Wireless Range Extender All rights reserved COPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement Country National restrictionsRestriction Reason/remark Product Description 150Mbps Wireless Range Extender DECLARATION OF CONFORMITYETSI EN 300 328 V1.7.1 ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN60950-12006 Package Contents CONTENTSHardware Installation Chapter 3 Quick Installation Guide Appendix C Troubleshooting Appendix B Factory DefaultsAppendix D Specifications Appendix A Application Example Conventions Package Contents Package Contents Overview of This GuideChapter 2 Hardware Installation Chapter3 Quick Installation Guide 4.6 DHCP Introduces how to set your AP to be a DHCP server sothat the AP will automatically assign an IP address for your PC Features 1.2 Main FeaturesChapter 1 Introduction 1.1 Product Overview 1.3.1 The Front Panel 1.3 AppearanceTL-WA730RE 150Mbps Wireless Range Extender User Guide LED Explanation Ensure the Range Extender is powered on before it restarts completely 1.3.2 The Rear Panel 2.3 Connecting the Device Chapter 2 Hardware Installation2.1 Before You Begin 2.2 Basic Requirements 1. Connect the Cable or DSL modem to a Router 3.1 Configure the PC Chapter 3 Quick Installation Guide TL-WA730RE 1 Select Use the following IP address 3.2 Quick Setup Figure 3-9 Quick Setup Figure 3-11 AP List Figure 3-12 Quick Setup - Range Extender Mode B. When you choose Access Point, take the following steps TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.1 Status Chapter 4 Configure the Device 4.3 QSS 4.2 Quick Setup Method One To add a new device Figure 4-3 Add A New Device Next TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.4 Network 4.5.1 Wireless Settings 4.5 Wireless TL-WA730RE 150Mbps Wireless Range Extender User Guide TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.2 Wireless Security 1 Range Extender ¾ WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key 2 Access Point TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.3 Wireless MAC Filtering To modify or delete an existing entry To set up an entry, follow these instructions 4.5.4 Wireless Advanced 4.5.5 Throughput Monitor 4.5.6 Wireless Statistics This page will be refreshed automatically every 5 seconds 4.6 DHCP 4.6.1 DHCP Settings 4.6.3 Address Reservation 4.6.2 DHCP Clients List The changes wont take effect until the device reboots 4.7 System ToolsTo Reserve IP addresses To modify A Reserved IP address 4.7.1 SNMP 4.7.2 Diagnostic Figure 4-23 Diagnostic 1 Only one user can use this tool at one time 4.7.3 Ping Watch Dog 4.7.4 Firmware Upgrade 4.7.6 Backup & Restore 4.7.5 Factory DefaultsTo upgrade the devices firmware, follow these instructions To restore the devices configuration, follow these instructions 4.7.7 Reboot2. Wrong process will lead the device unmanaged 4.7.9 System Log 4.7.8 Password Figure 4-31 System Log Appendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless Range Extender User Guide Default Value Appendix B Factory DefaultsCommon Default Settings Wireless 1. No LEDs are lit on the access point Appendix C Troubleshooting2. The LAN LED is not lit General Appendix D SpecificationsPhysical and Environment Appendix E Glossary TL-WA730RE 150Mbps Wireless Range Extender User Guide