DHCP Clients List, Address Reservation | TP-Link TL-WA730RE instruction

4.6.2 DHCP Clients List

TL-WA730RE150Mbps Wireless Range Extender User Guide

)Note:

1When the device is working on Dynamic IP mode, the DHCP Server function will be disabled.

2To use the DHCP server function of the device, you should configure all computers in the LAN as "Obtain an IP Address automatically" mode. This function will not take effect until the device reboots.

4.6.2 DHCP Clients List

Selecting DHCP > DHCP Clients List will enable you to view the Client Name, MAC Address, Assigned IP and Lease Time for each DHCP Client attached to the device (Figure 4-19).

Figure 4-19 DHCP Clients List

¾ID - Here displays the index of the DHCP client.

¾Client Name - Here displays the name of the DHCP client.

¾MAC Address - Here displays the MAC address of the DHCP client.

¾Assigned IP - Here displays the IP address that the AP has allocated to the DHCP client.

¾Lease Time - Here displays the time of the DHCP client leased. Before the time is up, DHCP client will request to renew the lease automatically.

You cannot change any of the values on this page. To update this page and to show the current attached devices, click on the Refresh button.

4.6.3 Address Reservation

Selecting DHCP > Address Reservation will enable you to specify a reserved IP address for a PC on the LAN, so the PC will always obtain the same IP address each time when it accesses the AP. Reserved IP addresses should be assigned to servers that require permanent IP settings. The screen below is used for address reservation (shown in Figure 4-20).

Figure 4-20 Address Reservation

39

Image 46

TP-Link manual DHCP Clients List, Address Reservation, TL-WA730RE 150Mbps Wireless Range Extender User Guide

Contents

TL-WA730RE 150Mbps Wireless Range Extender Rev 1.0.0 COPYRIGHT & TRADEMARKS All rights reserved CE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement Restriction National restrictionsCountry Reason/remark ETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 150Mbps Wireless Range Extender ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN60950-12006 Hardware Installation CONTENTSPackage Contents Chapter 3 Quick Installation Guide Appendix D Specifications Appendix B Factory DefaultsAppendix C Troubleshooting Appendix A Application Example Package Contents Conventions Chapter 2 Hardware Installation Overview of This GuidePackage Contents Chapter3 Quick Installation Guide that the AP will automatically assign an IP address for Introduces how to set your AP to be a DHCP server so4.6 DHCP your PC Chapter 1 Introduction 1.2 Main FeaturesFeatures 1.1 Product Overview TL-WA730RE 150Mbps Wireless Range Extender User Guide 1.3 Appearance1.3.1 The Front Panel LED Explanation 1.3.2 The Rear Panel Ensure the Range Extender is powered on before it restarts completely 2.1 Before You Begin Chapter 2 Hardware Installation2.3 Connecting the Device 2.2 Basic Requirements 1. Connect the Cable or DSL modem to a Router Chapter 3 Quick Installation Guide 3.1 Configure the PC 150Mbps Wireless Range Extender User Guide 1 Select Use the following IP address 3.2 Quick Setup Figure 3-9 Quick Setup Figure 3-12 Quick Setup - Range Extender Mode Figure 3-11 AP List B. When you choose Access Point, take the following steps TL-WA730RE 150Mbps Wireless Range Extender User Guide Chapter 4 Configure the Device 4.1 Status 4.2 Quick Setup 4.3 QSS To add a new device Method One Figure 4-3 Add A New Device Next TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.4 Network 4.5 Wireless 4.5.1 Wireless Settings TL-WA730RE 150Mbps Wireless Range Extender User Guide TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.2 Wireless Security 1 Range Extender ¾ WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key 2 Access Point TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.3 Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entry 4.5.4 Wireless Advanced 4.5.5 Throughput Monitor 4.5.6 Wireless Statistics 4.6 DHCP This page will be refreshed automatically every 5 seconds 4.6.1 DHCP Settings 4.6.2 DHCP Clients List 4.6.3 Address Reservation To Reserve IP addresses 4.7 System ToolsThe changes wont take effect until the device reboots To modify A Reserved IP address 4.7.1 SNMP 4.7.2 Diagnostic Figure 4-23 Diagnostic 4.7.3 Ping Watch Dog 1 Only one user can use this tool at one time 4.7.4 Firmware Upgrade 4.7.6 Backup & Restore 4.7.5 Factory DefaultsTo upgrade the devices firmware, follow these instructions To restore the devices configuration, follow these instructions 4.7.7 Reboot2. Wrong process will lead the device unmanaged 4.7.8 Password 4.7.9 System Log Figure 4-31 System Log Appendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless Range Extender User Guide Common Default Settings Appendix B Factory DefaultsDefault Value Wireless 1. No LEDs are lit on the access point Appendix C Troubleshooting2. The LAN LED is not lit General Appendix D SpecificationsPhysical and Environment Appendix E Glossary TL-WA730RE 150Mbps Wireless Range Extender User Guide