Throughput Monitor | TP-Link TL-WA730RE specification

TL-WA730RE150Mbps Wireless Range Extender User Guide

¾Tx Power - Specifies the transmit power of the device. You can select High, Middle or Low which you would like. High is the default setting and is recommended.

¾Beacon Interval - Specifies a value between 20-1000 milliseconds. The beacons are the packets sent by the device to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100.

¾RTS Threshold - Specifies the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the device will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346.

¾Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance since excessive packets. 2346 is the default setting and is recommended.

¾DTIM Interval - Determines the interval of the Delivery Traffic Indication Message (DTIM). You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval.

¾Enable WMM - WMM function can guarantee the packets with high- priority messages being transmitted preferentially. It is strongly recommended enabled.

¾Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time.

¾Enable AP Isolation - Isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled.

4.5.5 Throughput Monitor

Selecting Wireless > Throughput Monitor will helps to watch wireless throughput information in the following screen shown in Figure 4-15.

35

Image 42

TP-Link manual Throughput Monitor, TL-WA730RE 150Mbps Wireless Range Extender User Guide

Contents

TL-WA730RE 150Mbps Wireless Range Extender Rev 1.0.0 COPYRIGHT & TRADEMARKS All rights reserved FCC STATEMENT CE Mark WarningFCC RF Radiation Exposure Statement Restriction National restrictionsCountry Reason/remark ETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 150Mbps Wireless Range Extender ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN60950-12006 Hardware Installation CONTENTSPackage Contents Chapter 3 Quick Installation Guide Appendix D Specifications Appendix B Factory DefaultsAppendix C Troubleshooting Appendix A Application Example Package Contents Conventions Chapter 2 Hardware Installation Overview of This GuidePackage Contents Chapter3 Quick Installation Guide that the AP will automatically assign an IP address for Introduces how to set your AP to be a DHCP server so4.6 DHCP your PC Chapter 1 Introduction 1.2 Main FeaturesFeatures 1.1 Product Overview TL-WA730RE 150Mbps Wireless Range Extender User Guide 1.3 Appearance1.3.1 The Front Panel LED Explanation 1.3.2 The Rear Panel Ensure the Range Extender is powered on before it restarts completely 2.1 Before You Begin Chapter 2 Hardware Installation2.3 Connecting the Device 2.2 Basic Requirements 1. Connect the Cable or DSL modem to a Router Chapter 3 Quick Installation Guide 3.1 Configure the PC 150Mbps Wireless Range Extender User Guide 1 Select Use the following IP address 3.2 Quick Setup Figure 3-9 Quick Setup Figure 3-12 Quick Setup - Range Extender Mode Figure 3-11 AP List B. When you choose Access Point, take the following steps TL-WA730RE 150Mbps Wireless Range Extender User Guide Chapter 4 Configure the Device 4.1 Status 4.2 Quick Setup 4.3 QSS To add a new device Method One Figure 4-3 Add A New Device Next TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.4 Network 4.5 Wireless 4.5.1 Wireless Settings TL-WA730RE 150Mbps Wireless Range Extender User Guide TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.2 Wireless Security 1 Range Extender ¾ WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key 2 Access Point TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.3 Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entry 4.5.4 Wireless Advanced 4.5.5 Throughput Monitor 4.5.6 Wireless Statistics 4.6 DHCP This page will be refreshed automatically every 5 seconds 4.6.1 DHCP Settings 4.6.2 DHCP Clients List 4.6.3 Address Reservation To Reserve IP addresses 4.7 System ToolsThe changes wont take effect until the device reboots To modify A Reserved IP address 4.7.1 SNMP 4.7.2 Diagnostic Figure 4-23 Diagnostic 4.7.3 Ping Watch Dog 1 Only one user can use this tool at one time 4.7.4 Firmware Upgrade 4.7.5 Factory Defaults 4.7.6 Backup & RestoreTo upgrade the devices firmware, follow these instructions 4.7.7 Reboot To restore the devices configuration, follow these instructions2. Wrong process will lead the device unmanaged 4.7.8 Password 4.7.9 System Log Figure 4-31 System Log Appendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless Range Extender User Guide Common Default Settings Appendix B Factory DefaultsDefault Value Wireless Appendix C Troubleshooting 1. No LEDs are lit on the access point2. The LAN LED is not lit Appendix D Specifications GeneralPhysical and Environment Appendix E Glossary TL-WA730RE 150Mbps Wireless Range Extender User Guide