Manuals / TRENDnet / Computer Equipment / Printer

TRENDnet TEW-P1P, TEW-P1U manual Your wireless print server has been successfully configured

Models: TEW-P1P TEW-P1U

1 83

Download 83 pages 52.6 Kb

Page 17

12. Your wireless print server has been successfully configured.

11. In this page, you can confirm your setting value again. Click NEXT.

12. Your wireless print server has been successfully configured.

15

Image 17

TRENDnet TEW-P1P, TEW-P1U manual Your wireless print server has been successfully configured

Contents

Page Page 6. NETWORK PRINT MONITOR 7. TCP/IP LPR PORT PRINTING INSTALLATION8.UPGRADING PRINT SERVER 9. TROUBLESHOOTINGAPPENDIX UPGRADING THE PRINT SERVER FROM WINDOWS NT/2000/XP THROUGH TCP/IPCopyright TrademarksFCC Compliance Notice Radio Frequency Notice Important Note FCC Radiation Exposure StatementWireless Specifications Network configuration1. Introduction Product OverviewBefore you start, you should prepare Components and Features Wireless Print serverHardware Installation Ad-hoc PEER-to-PEER Mode Wireless Network EnvironmentInfrastructure AP Mode Configuration Solution Table 2. Print Server InstallationSetup Operating PreparationComment 3.The Setup Utility for Windows-basedTo install Wizard, please follow the directions listed below Installing the Setup Wizard5. Click Wireless Setup Wizard and the following message appear 4. After installation completes, the Setup Wizard message appearsPage Data Transmit Rates： Auto or 1,2Mbps, 5.5Mbps or 11Mbps Click NEXT Channel： optional9. Choose Enable the WEP Encryption as you need, and click NEXT 12. Your wireless print server has been successfully configured Page Page Page Using PSAdmin TCP/IP Wizard WizardNetWare Wizard Manual Setup Specify an IP address Properties -TCP/IP OptionsObtain an IP address from a DHCP server Upgrade Refresh ResetMultiple Print Queues Configuration 3. Click Change or Remove Programs tab Uninstalling the PSAdmin on Windows PCProcedure 4.Internet Printer Connection and HP Web JetAdmin IPP OverviewWindows NT/2000/XP/2003 Three ports should be the port name as lp1, lp2, and lp3 One port should be the port name as lp1System Requirements HP Web JetAdmin OverviewConfiguring and Modifying a Device Installing HP Web JetAdminConfirming Installation and Supply Access Removing HP Web JetAdmin Utility Using Embedded Web Server 5. Configuration from Embedded Web ServerOverview Status MenuSystem Status Printer Status Wireless StatusTCP/IP Status Netware Status NetWare NDS Setting General SettingsNetWare Bindery Setting SNMP StatusAppleTalk Status Setup Menu Preparation System SetupRe-type Password Basic Settings Wireless SetupTCP/IP Status WEP SettingsNetWare Setup Installing Print Server on NetWare 4.x/5.x 2. Select “NCF files options” 3. Select “Edit AUTOEXEC.NCF file” Installation ProcedureSNMP Setup system.sysContact snmp.snmpEnableAuthenTrapssystem.sysName system.sysLocationAppleTalk Setup recommended Preparation Setting Up a Macintosh Computer6. Network Print Monitor TCP/IP TCP/IP Protocol InstallationIPX/SPX NetBEUI7. Restart the computer IPX/SPX-compatible Protocol InstallationNetBEUI Protocol Installation 12. Select Printer and Properties Windows 95/98/Me/NT/2000/XP Installation Procedure15. Select the Network Print Port and click OK Uninstalling Network Print Port on Windows 95/98/Me/NT/2000/XP 7. TCP/IP LPR Port Printing InstallationBasic TCP/IP Installation Overview 3. Click Add/Remove tabAssigning an IP Address Windows NT LPR Port Printing InstallationDHCP 1. Use the Network Print Monitor utilityWindows 2000/XP Standard TCP/IP Port Printing Installation 2. Run Add Printer, Click Next 9. Click Finish Note Please DO NOT type any other name than lp1 in this step8. Click OK, and Next 13. Done 1. Login root 2. Type “arp -s IP address Print server‘s node ID” UNIX InstallationSCO UNIX OpenServer 4. Type “tftp Print server‘s IP address”i. Do you want to install or remove printing i/r/q? q ------- q a. Do you want to install or remove printing i/r/q ? q1. Login root 2. Type “arp -s IP address Print server‘s node ID” SUN Solaris13. Type “enable printer-1” For example enable printer-1 11. Type “lpadmin -pprinter-1 -s Print server‘s IP address”IBM AIX 9. Type “tftp Print server‘s IP address”Redhat Linux e. Open Printer Configuration5. Select Printer/Plotter 6. Select Printer Spooling 7. Select Add a Print Queuef. Click New button g. Click Forward button h. In the Name field, type a user-defined name, click Forward i. In the Queue Type field, choose Networked UNIXj. In the Server field, type the IP of print server l. Click Forward buttonn. Choose the model of printer and click Forward o. Done m. In the Printer field, choose Postscript Printer5. Select Print Setup Manager from System Administration window 4. Select SCO AdminUnixWare 2. Run CDE Common Desktop Environment1. Upgrading the print server from PSAdmin Upgrading the print server from PSAdmin8.Upgrading Print Server Upgrading the print server from Windows NT/2000/XP Through TCP/IP3. Type “tftp print server’s IP address” Upgrading the print server from UNIXThrough TCP/IPUpgrading the print server from Browser 5. Click Upgrade 6. Done 4. Click Upgrade form Browser and select the firmware fileGeneral Troubleshooting Overview 9. TroubleshootingPower Related Problems Print Port Related ProblemsMulti-Segment Frame Type 802.2 Installation Windows 95/98/Me/NT/2000/XP TroubleshootingRIP for NWLink IPX/SPX compatible transport Installation Procedure 3. Select Control PanelPrint server Reconfiguration Procedure on Windows NT Print Server Reconfiguration Procedure on Windows 95/98/MeMoving the print server to A New Segment 12. Restart the computerMoving Your Computer to A New Segment Novell NetWare TroubleshootingTCP/IP Troubleshooting a.If the gateway computer is a NT/UNIX server 8. Move the print server back to the Segment B 9. Done 5. Type edit config.txt to modify this configuration fileAppendix Diagnostic ModeLoad Default Value Question C Frequently Asked QuestionsQuestion B The Status LED light keeps blinking after POST Question DQuestion E Question FPanasonic KX-P6100/6300/6500 Additional Installation Instructions