Manuals / TRENDnet / Computer Equipment / Printer

TRENDnet TEW-P1P, TEW-P1U manual Additional Installation Instructions, Panasonic KX-P6100/6300/6500

Models: TEW-P1P TEW-P1U

1 83

Page 83

Additional Installation Instructions

Panasonic KX-P6100/6300/6500

If you are using a Panasonic KX-P6100/6300/6500 laser printer with the print server through the Network Print Port under Windows 95/98, please redirect the printer named “Panasonic KX-P6100 PCL” or “Panasonic KX-P6300 PCL”, or “Panasonic KX-P6500 PCL” to the print server through the Network Print Port.

DO NOT redirect the printer named “Panasonic KX-P6100 GDI”, “Panasonic KX-P6300 GDI”, or “Panasonic KX-P6500 GDI” to the print server.

Page 83

Image 83

TRENDnet TEW-P1P, TEW-P1U manual Additional Installation Instructions, Panasonic KX-P6100/6300/6500

Contents

Page Page 6. NETWORK PRINT MONITOR 7. TCP/IP LPR PORT PRINTING INSTALLATIONUPGRADING THE PRINT SERVER FROM WINDOWS NT/2000/XP THROUGH TCP/IP 9. TROUBLESHOOTING8.UPGRADING PRINT SERVER APPENDIXImportant Note FCC Radiation Exposure Statement TrademarksCopyright FCC Compliance Notice Radio Frequency NoticeProduct Overview Network configurationWireless Specifications 1. IntroductionBefore you start, you should prepare Components and Features Wireless Print serverHardware Installation Ad-hoc PEER-to-PEER Mode Wireless Network EnvironmentInfrastructure AP Mode Preparation 2. Print Server InstallationConfiguration Solution Table Setup OperatingComment 3.The Setup Utility for Windows-basedTo install Wizard, please follow the directions listed below Installing the Setup Wizard5. Click Wireless Setup Wizard and the following message appear 4. After installation completes, the Setup Wizard message appearsPage Data Transmit Rates： Auto or 1,2Mbps, 5.5Mbps or 11Mbps Click NEXT Channel： optional9. Choose Enable the WEP Encryption as you need, and click NEXT 12. Your wireless print server has been successfully configured Page Page Page Using PSAdmin TCP/IP Wizard WizardNetWare Wizard Manual Setup Specify an IP address Properties -TCP/IP OptionsObtain an IP address from a DHCP server Upgrade Refresh ResetMultiple Print Queues Configuration 3. Click Change or Remove Programs tab Uninstalling the PSAdmin on Windows PCProcedure 4.Internet Printer Connection and HP Web JetAdmin IPP OverviewWindows NT/2000/XP/2003 Three ports should be the port name as lp1, lp2, and lp3 One port should be the port name as lp1System Requirements HP Web JetAdmin OverviewConfiguring and Modifying a Device Installing HP Web JetAdminConfirming Installation and Supply Access Removing HP Web JetAdmin Utility Status Menu 5. Configuration from Embedded Web ServerUsing Embedded Web Server OverviewSystem Status Printer Status Wireless StatusTCP/IP Status Netware Status SNMP Status General SettingsNetWare NDS Setting NetWare Bindery SettingAppleTalk Status Setup Menu Preparation System SetupRe-type Password Basic Settings Wireless SetupTCP/IP Status WEP SettingsNetWare Setup Installing Print Server on NetWare 4.x/5.x 2. Select “NCF files options” 3. Select “Edit AUTOEXEC.NCF file” Installation ProcedureSNMP Setup system.sysLocation snmp.snmpEnableAuthenTrapssystem.sysContact system.sysNameAppleTalk Setup recommended Preparation Setting Up a Macintosh Computer6. Network Print Monitor NetBEUI TCP/IP Protocol InstallationTCP/IP IPX/SPX7. Restart the computer IPX/SPX-compatible Protocol InstallationNetBEUI Protocol Installation 12. Select Printer and Properties Windows 95/98/Me/NT/2000/XP Installation Procedure15. Select the Network Print Port and click OK 3. Click Add/Remove tab 7. TCP/IP LPR Port Printing InstallationUninstalling Network Print Port on Windows 95/98/Me/NT/2000/XP Basic TCP/IP Installation Overview1. Use the Network Print Monitor utility Windows NT LPR Port Printing InstallationAssigning an IP Address DHCPWindows 2000/XP Standard TCP/IP Port Printing Installation 2. Run Add Printer, Click Next 9. Click Finish Note Please DO NOT type any other name than lp1 in this step8. Click OK, and Next 13. Done 4. Type “tftp Print server‘s IP address” UNIX Installation1. Login root 2. Type “arp -s IP address Print server‘s node ID” SCO UNIX OpenServerSUN Solaris a. Do you want to install or remove printing i/r/q ? qi. Do you want to install or remove printing i/r/q? q ------- q 1. Login root 2. Type “arp -s IP address Print server‘s node ID”9. Type “tftp Print server‘s IP address” 11. Type “lpadmin -pprinter-1 -s Print server‘s IP address”13. Type “enable printer-1” For example enable printer-1 IBM AIX7. Select Add a Print Queue e. Open Printer ConfigurationRedhat Linux 5. Select Printer/Plotter 6. Select Printer Spoolingf. Click New button g. Click Forward button l. Click Forward button i. In the Queue Type field, choose Networked UNIXh. In the Name field, type a user-defined name, click Forward j. In the Server field, type the IP of print servern. Choose the model of printer and click Forward o. Done m. In the Printer field, choose Postscript Printer2. Run CDE Common Desktop Environment 4. Select SCO Admin5. Select Print Setup Manager from System Administration window UnixWareUpgrading the print server from Windows NT/2000/XP Through TCP/IP Upgrading the print server from PSAdmin1. Upgrading the print server from PSAdmin 8.Upgrading Print Server3. Type “tftp print server’s IP address” Upgrading the print server from UNIXThrough TCP/IPUpgrading the print server from Browser 5. Click Upgrade 6. Done 4. Click Upgrade form Browser and select the firmware filePrint Port Related Problems 9. TroubleshootingGeneral Troubleshooting Overview Power Related Problems3. Select Control Panel Windows 95/98/Me/NT/2000/XP TroubleshootingMulti-Segment Frame Type 802.2 Installation RIP for NWLink IPX/SPX compatible transport Installation Procedure12. Restart the computer Print Server Reconfiguration Procedure on Windows 95/98/MePrint server Reconfiguration Procedure on Windows NT Moving the print server to A New SegmentMoving Your Computer to A New Segment Novell NetWare TroubleshootingTCP/IP Troubleshooting a.If the gateway computer is a NT/UNIX server 8. Move the print server back to the Segment B 9. Done 5. Type edit config.txt to modify this configuration fileAppendix Diagnostic ModeLoad Default Value Question C Frequently Asked QuestionsQuestion B Question F Question DThe Status LED light keeps blinking after POST Question EPanasonic KX-P6100/6300/6500 Additional Installation Instructions