Manuals / TRENDnet / Computer Equipment / Printer

TRENDnet TEW-P1U, TEW-P1P manual Upgrading Print Server, Troubleshooting, Appendix

Models: TEW-P1P TEW-P1U

1 83

Page 4

8.UPGRADING PRINT SERVER	68
OVERVIEW	68
UPGRADING THE PRINT SERVER FROM PSADMIN	68
U PGRADING THE PRINT SERVER FROM W INDOWS NT/2000/XP (T HROUGH TCP/IP)	68
UPGRADING THE PRINT SERVER FROM UNIX (THROUGH TCP/IP)	69
UPGRADING THE PRINT SERVER FROM BROWSER	69
9. TROUBLESHOOTING	71
GENERAL TROUBLESHOOTING OVERVIEW	71
POWER RELATED PROBLEMS	71
PRINT PORT RELATED PROBLEMS	71
WINDOWS 95/98/ME/NT/2000/XP TROUBLESHOOTING	72
MOVING THE PRINT SERVER TO A NEW SEGMENT	73
MOVING YOUR COMPUTER TO A NEW SEGMENT	74
NOVELL NETWARE TROUBLESHOOTING	74
TCP/IP TROUBLESHOOTING	74
APPENDIX:	77
LOAD DEFAULT VALUE	78
FREQUENTLY ASKED QUESTIONS	79
ADDITIONAL INSTALLATION INSTRUCTIONS	81

Page 4

Image 4

TRENDnet TEW-P1U, TEW-P1P manual Upgrading Print Server, Troubleshooting, Appendix

Contents

Page Page 7. TCP/IP LPR PORT PRINTING INSTALLATION 6. NETWORK PRINT MONITOR9. TROUBLESHOOTING 8.UPGRADING PRINT SERVERAPPENDIX UPGRADING THE PRINT SERVER FROM WINDOWS NT/2000/XP THROUGH TCP/IPTrademarks CopyrightFCC Compliance Notice Radio Frequency Notice Important Note FCC Radiation Exposure StatementNetwork configuration Wireless Specifications1. Introduction Product OverviewComponents and Features Wireless Print server Before you start, you should prepareHardware Installation Infrastructure AP Mode Wireless Network EnvironmentAd-hoc PEER-to-PEER Mode 2. Print Server Installation Configuration Solution TableSetup Operating Preparation3.The Setup Utility for Windows-based CommentInstalling the Setup Wizard To install Wizard, please follow the directions listed below4. After installation completes, the Setup Wizard message appears 5. Click Wireless Setup Wizard and the following message appearPage Channel： optional Data Transmit Rates： Auto or 1,2Mbps, 5.5Mbps or 11Mbps Click NEXT9. Choose Enable the WEP Encryption as you need, and click NEXT 12. Your wireless print server has been successfully configured Page Page Page Using PSAdmin Wizard TCP/IP WizardNetWare Wizard Manual Setup Obtain an IP address from a DHCP server Properties -TCP/IP OptionsSpecify an IP address Upgrade Multiple Print Queues Configuration ResetRefresh Procedure Uninstalling the PSAdmin on Windows PC3. Click Change or Remove Programs tab Windows NT/2000/XP/2003 IPP Overview4.Internet Printer Connection and HP Web JetAdmin One port should be the port name as lp1 Three ports should be the port name as lp1, lp2, and lp3HP Web JetAdmin Overview System RequirementsConfirming Installation and Supply Access Installing HP Web JetAdminConfiguring and Modifying a Device Removing HP Web JetAdmin Utility 5. Configuration from Embedded Web Server Using Embedded Web ServerOverview Status MenuSystem Status Wireless Status Printer StatusTCP/IP Status Netware Status General Settings NetWare NDS SettingNetWare Bindery Setting SNMP StatusAppleTalk Status Setup Menu Re-type Password System SetupPreparation Wireless Setup Basic SettingsWEP Settings TCP/IP StatusNetWare Setup Installing Print Server on NetWare 4.x/5.x SNMP Setup Installation Procedure2. Select “NCF files options” 3. Select “Edit AUTOEXEC.NCF file” snmp.snmpEnableAuthenTraps system.sysContactsystem.sysName system.sysLocationAppleTalk Setup recommended 6. Network Print Monitor Setting Up a Macintosh ComputerPreparation TCP/IP Protocol Installation TCP/IPIPX/SPX NetBEUINetBEUI Protocol Installation IPX/SPX-compatible Protocol Installation7. Restart the computer Windows 95/98/Me/NT/2000/XP Installation Procedure 12. Select Printer and Properties15. Select the Network Print Port and click OK 7. TCP/IP LPR Port Printing Installation Uninstalling Network Print Port on Windows 95/98/Me/NT/2000/XPBasic TCP/IP Installation Overview 3. Click Add/Remove tabWindows NT LPR Port Printing Installation Assigning an IP AddressDHCP 1. Use the Network Print Monitor utilityWindows 2000/XP Standard TCP/IP Port Printing Installation 2. Run Add Printer, Click Next 8. Click OK, and Next Note Please DO NOT type any other name than lp1 in this step9. Click Finish 13. Done UNIX Installation 1. Login root 2. Type “arp -s IP address Print server‘s node ID”SCO UNIX OpenServer 4. Type “tftp Print server‘s IP address”a. Do you want to install or remove printing i/r/q ? q i. Do you want to install or remove printing i/r/q? q ------- q1. Login root 2. Type “arp -s IP address Print server‘s node ID” SUN Solaris11. Type “lpadmin -pprinter-1 -s Print server‘s IP address” 13. Type “enable printer-1” For example enable printer-1IBM AIX 9. Type “tftp Print server‘s IP address”e. Open Printer Configuration Redhat Linux5. Select Printer/Plotter 6. Select Printer Spooling 7. Select Add a Print Queuef. Click New button g. Click Forward button i. In the Queue Type field, choose Networked UNIX h. In the Name field, type a user-defined name, click Forwardj. In the Server field, type the IP of print server l. Click Forward buttonm. In the Printer field, choose Postscript Printer n. Choose the model of printer and click Forward o. Done4. Select SCO Admin 5. Select Print Setup Manager from System Administration windowUnixWare 2. Run CDE Common Desktop EnvironmentUpgrading the print server from PSAdmin 1. Upgrading the print server from PSAdmin8.Upgrading Print Server Upgrading the print server from Windows NT/2000/XP Through TCP/IPUpgrading the print server from Browser Upgrading the print server from UNIXThrough TCP/IP3. Type “tftp print server’s IP address” 4. Click Upgrade form Browser and select the firmware file 5. Click Upgrade 6. Done9. Troubleshooting General Troubleshooting OverviewPower Related Problems Print Port Related ProblemsWindows 95/98/Me/NT/2000/XP Troubleshooting Multi-Segment Frame Type 802.2 InstallationRIP for NWLink IPX/SPX compatible transport Installation Procedure 3. Select Control PanelPrint Server Reconfiguration Procedure on Windows 95/98/Me Print server Reconfiguration Procedure on Windows NTMoving the print server to A New Segment 12. Restart the computerTCP/IP Troubleshooting Novell NetWare TroubleshootingMoving Your Computer to A New Segment a.If the gateway computer is a NT/UNIX server 5. Type edit config.txt to modify this configuration file 8. Move the print server back to the Segment B 9. DoneDiagnostic Mode AppendixLoad Default Value Question B Frequently Asked QuestionsQuestion C Question D The Status LED light keeps blinking after POSTQuestion E Question FAdditional Installation Instructions Panasonic KX-P6100/6300/6500

8.UPGRADING PRINT SERVER

UPGRADING THE PRINT SERVER FROM WINDOWS NT/2000/XP (THROUGH TCP/IP)

9. TROUBLESHOOTING

APPENDIX:

U PGRADING THE PRINT SERVER FROM W INDOWS NT/2000/XP (T HROUGH TCP/IP)