Unified Brands HY-6E(CE) To Install, 10.23Door Removal/Installation/Alignment P/N, To Align

5.The hose may be removed. Be careful that the hose clamps do not fall off and get lost.

IMPORTANT: Make sure that the correct part (and part number) are being used. The two hoses in the steamer are of different lengths. (See Page 17 for Part Numbers.)

To Install:

6.Slide the two hose clamps onto the hose and position the hose adjacent to the steam port and steam generator.

7.Slide the hose onto the hose nipple on the steam port and at the other end, onto the steam generator nipple. Make sure the hose is on all the way so that the end of the hose is against the face of the nipples.

8.Install the hose clamps 5/64" (2 mm) from the end of the hose.

10.23Door Removal/Installation/Alignment P/N 094150

1.To remove the door, turn off the steamer power and allow the steamer to cool. Then, remove door by supporting the weight of the door and remove hinge pin.

2.Place the door on a flat, clean table or similar support, with gasket facing up. Be careful not to scratch door surface.

3.Inspect door gasket for signs of cuts or other defects which may impair its function. Replace if necessary.

To Install:

4.To install the door, apply NEVER-SEEZ lubricant to hinge pin. Align door with hinge and insert hinge pin, or apply Locktite 242 to the door-to-hinge bolts, then install door and mounting bolts. Do NOT tighten mounting bolts at this time.

To Align:

5.Place a piece of masking tape over the door pin (bullet) hole in the door.

6.Close the door until the door pin just penetrates the masking tape. Make sure the door pin contacts only the door latch spring.

7.If door pin does not strike the center of the masking tape or spring hole in the U-channel, loosen the hinge-to-oven bolts and align the door to the door pin. Tighten hinge-to-oven mounting bolts.

8.You should be able to pull a dollar bill or comparable piece of paper smoothly between the gasket and oven cavity with the door closed. To adjust the hinge side, loosen the door-to-hinge bolts and align the door gasket with the oven cavity. Tighten the door-to-hinge mounting bolts. To adjust the bullet side refer to 10.29.

9.Operate oven in steam mode and check for leaks.

10.24Door Switch P/N 096857

1.From the right side of the steamer with panel removed, unplug the door switch from the cable harness.

2.The switch (for normal door opening) is held in place with two small 4-40 screws. With a flat blade screwdriver, remove these screws and the switch may be removed.

3.To install 4-40 screws for the door switch use a screw starter.

4.If the door has been reversed and the switch must be removed and replaced, refer to the top and left side panel removal in Section 10.3 and then remove the switch as above.

10.25Door Reversing Procedures

1.Turn off steamer power and allow steamer to cool.

2.To remove door, support door while removing hinge- to-steamer bolts.

3.Place door with hinge on a flat, clean table (or similar support), with the gasket facing up. Be careful not to scratch door surface.

4.Note and record distance between lock nut and end of door locking pin (bullet). This information will be needed during bullet installation described in Step 6.

5.Loosen lock nut with a wrench. Remove door locking pin and lock nut.

6.Coat bullet threads with NEVER-SEEZ high temperature compound. Install door locking pin and lock nut directly across steamer cavity from old door locking pin location. Install these items so that lock nut-to-end of bullet distance is approximately the same as measured in Step 4.

7.Remove the two 1/4-20 truss head screws from above and below the old bullet location and install them above and below the new bullet location.

28 OM/SM-HY-6E(CE)