5.Attach new drain valve to valve bracket. Pull silicone hose through drain valve and loosely install hose clamps over both ends of the hose. Be sure silicone hose is properly aligned and does not have any kinks, bends and/or twists.

6.Position the valve over the valve mounting threaded studs and connect both ends of the hose to the drain box and steam generator.

7.Position the clamps so that the worm screw may be easily tightened. Using a 7mm nutdriver, tighten both hose clamps. Be careful not to overtighten clamps as it may cut hose.

8.Install and tighten valve mounting 10-32 cap nuts.

9.Plug valve electrical leads into the wiring harness.

To Test:

Operate steamer and allow steam generator to fill. Check for leaks and observe if drain valve fully closes. Turn off steamer and observe that drain valve opens and the steam generator drains. Install back cover.

10.6Water Inlet Valve - Three Way P/N 090827

1.Turn off power to the steamer. Turn off the water supply to the steamer. Remove the water supply hose connection on the rear of the steamer.

2.As viewed from the rear, remove the back panel and the right panel.

3.The water inlet of the valve branches to three individual solenoid activated valves within a single housing, with the following sets of wires:

Solenoid

Wires

Top Steam Generator Fill: Green and Blue

Bottom Steam Generator Fill: Violet and Gray

Condensate Spray:

Black and White

4.Using a 7mm nutdriver, loosen the three hose clamps on the water inlet valve.

5.Slide the hose clamps down the hose until needed for reassembly. Loosen and remove the hoses using a gentle rocking motion.

6.From the back of the steamer, remove the two screws holding the valve assembly in place. Then lower the valve WITH THE WIRES STILL ATTACHED.

7.From the back of the steamer, remove the two 8-32 screws holding the valve assembly in place. Lower the valve.

8.Carefully unplug the connectors, one at a time and attach to the new valve.

9.To install a new valve, reverse the procedures and first install the six wires (three sets) as listed in Item 3 of this Section. Fasten the valve to the steamer with the two screws. Make sure that the valve is NOT installed upside down.

10.Re-attach the hoses to the valve. Slide the hoses all the way so that the end of the hose is flush against the face of the valve.

IMPORTANT. Make sure that the correct steam generator hose is connected to the corresponding valve outlet. Slide the hose clamps back into position around the end of the hose and tighten the clamps.

CAUTION: Do not overtighten these clamps as that may damage the valve.

Slide the hose clamps so that they are within 1/8 inch (3 mm) from the end of the hose.

TOP hose — to the TOP Steam Generator MIDDLE hose — to the BOTTOM Steam Generator BOTTOM hose — to the DRAIN Box

11.Attach the three sets of wires to the valve making sure that the proper wires are connected to the corresponding terminals.

To Test:

With power ON, turn on the power switch to one cavity. The fill solenoid for that steam generator should energize allowing water to enter the steam generator. When READY light is ON, spray valve solenoid should energize and water should enter the drain box.

10.7 Water Inlet Valve Coil

If a solenoid coil on the water inlet valve is defective, replace the entire valve in accordance with Section 10.6.

10.8Drain Box Spray Nozzle P/N 081670

1.Raise the stainless steel vent pipe to remove it from the drain box. Do not loosen the hose clamp around the vent pipe. The hose clamp serves to prevent the pipe from going too far into the drain box. Secure the vent pipe in the raised position.

22 OM/SM-HY-6E(CE)

Page 21 Page 23
Page 22
Image 22
Unified Brands HY-6E(CE) To Test, Water Inlet Valve Three Way P/N, Water Inlet Valve Coil, Drain Box Spray Nozzle P/N
Page 21 Page 23

HY-6E(CE) specifications

Unified Brands HY-6E(CE) is a state-of-the-art cooking appliance specifically designed for professional kitchens, providing top-notch technology, efficiency, and capability. This equipment stands out due to its combination of advanced features and user-friendly controls, making it an ideal choice for restaurants, catering services, and foodservice operations.

One of the most notable features of the HY-6E(CE) is its powerful heating system, which allows for rapid cooking times and consistent results. The unit is equipped with a high-efficiency burner system that ensures even heat distribution while minimizing energy consumption. This innovative technology not only enhances cooking performance but also contributes to cost savings in energy usage.

Another significant characteristic of the HY-6E(CE) is its versatility. The appliance supports various cooking methods, including boiling, frying, steaming, and simmering, making it suitable for a wide range of culinary applications. This adaptability enables chefs to prepare multiple dishes simultaneously, thereby increasing kitchen productivity.

The design of the HY-6E(CE) emphasizes durability and ease of maintenance. Constructed from high-grade stainless steel, it is built to withstand the rigors of a busy kitchen while resisting corrosion and wear. The smooth surfaces and streamlined design facilitate quick cleaning, ensuring that hygiene standards are upheld without excessive downtime.

In terms of control and monitoring, the HY-6E(CE) features an intuitive digital interface that allows chefs to set precise temperature and timing. This level of control is crucial for maintaining culinary consistency and quality, especially in high-pressure environments. The appliance also includes safety features such as automatic shut-off and flame failure protection, ensuring a safe cooking experience.

The HY-6E(CE) is further enhanced with smart technology options that enable remote monitoring and adjustments via mobile applications. This connectivity allows operators to oversee kitchen operations from any location, optimizing workflow and ensuring that meal preparation runs smoothly.

In conclusion, the Unified Brands HY-6E(CE) is an exemplary cooking appliance that merges efficiency, versatility, and advanced technology. Its features cater to the dynamic needs of the modern kitchen, making it a valuable addition for culinary professionals who prioritize performance and reliability in their cooking operations.
Top Page Image Contents