Vertex Standard VXA-700 MENU Listing

MENU (“SET”) MODE

MENU Listing

A listing of the Menu items available via the SET mode may be found below.

	Set Mode Item	Function	AvailableValuesø
	1. Scan Lamp	Enables/Disables the Scan lamp while paused dur-	On/Off
		ing scanning.
	2. Backlight	Selects the Display illumination Mode.	Key/Off/On
	3. Large Font	Selects the frequency display between the “Large	Off/On
		Character” and “Small Character” modes.
1. Display	4. Contrast	Setting of the display contrast.	00 - 15 (06)
	5. Dimmer	Setting of the display brightness level.	LV 1 - LV 4 (LV 3)
	6. Meter Symbol	Selects the S- & TX PO meter symbol.	Four patterns
	7. Display Mode	Selects the display of the sensor units’ information.	Off/Temp/Volt
	8. RX LED	Edits the BUSY indicator color.	–
	9. TX LED	Edits the TX indicator color.	–
	10. EMG LED	Edits the Emergency lamp color.	–
	11. Alert LED	Edits the Weather Alert lamp color.	–
	12. TEMP LED	Edits the Over Heating lamp color.	–
Sound	1. Beeper	Select the Keypad beeper tone.	On/DTMF/Off
	2. Bell	Enables/disables the Bell Ringer function.	On/Off
	3. Power On Beep	Selects the Power-on beep.	Off/1/2/3
2.
	4. ARTS Beep	Selects the beep option during ARTS operation.	On/Off
	1. SQL	Sets the Squelch threshold level for the AM and FM	0 - 8
		Narrow modes.	(2)
	2. WSQL	Sets the Squelch threshold level for the Wide FM	0 - 8
		mode.	(1)
	3.Resume	Selects the Scan Resume mode.	5secs/Busy
	4. DW/PRI	Selects the Dual Watch/Priority Function.	DW/PRI
	5. RX Save	Selects the Receive-mode Battery Saver “sleep” ra-	ABS/1:1/1:2/1:3/1:4/1:5/
Receiver		tio.	Off
	6. Step	Setting of the synthesizer steps.	5k/10k/12.5k/15k/20k/
			25k/50k/100k
	7. SQL Type	Selects the Tone Encoder and/or Decoder mode.	Off/T/TSQ/DCS
3.
	8. TONE Set	Setting of the CTCSS Tone Frequency.	50 standard
			CTCSS tones.
	9. DCS Set	Setting of the DCS Code.	104 standard DCS
			codes.
	10. PRI Time	Selects the Priority Checking Time.	500ms/1s/1.5s/2s/
			2.5s/3s
	11. SPECT Width	Selects the visible bandwidth of the Spectrum Ana-	±30ch/±15ch
		lyzer.

	Set Mode Item	Function	AvailableValuesø
	1. RPT Shift	Set the Repeater Shift Direction.	Simplex / –RPT / +RPT
	2. Shift Width	Sets the magnitude of the Repeater Shift.	00kHz – 9.95MHz
			(0.6kHz)
Transmit	3. ARS	Enables/disables the Automatic Repeater Shift func-	On/Off
		tion.
	4. ARTS	Enables/disables ARTS operation.	Off / RX / TX / TRX
	5. ARTS Itvl	Selects the polling interval during ARTS operation.	15secs / 25secs
4.
	6. T.O.T	Setting of the Time-Out Timer Countdown Time.	Off / 1min / 3min / 5min
	7. TX Power	Selects the TX Output Power on the FM mode.	Low1 / Low2 / Low3 /
			High
	1. Lock Mode	Selects the Control Locking lockout combination.	DIAL / KEY / KEY+DIAL /
			PTT / DIAL+PTT /
			KEY+PTT / ALL
Set	2. [MON]	Selects the MONITOR button (just below the PTT	MON / T.CALL
		switch) function.
5.Key	3. [121.5]	Selects the primary [121.5(HOME)] key function	121.5/HOME
	4. USER 1	Programming the [USER] key assignment (momen-	ANL / TX Power / ARTS /
		tary-press mode).
			XFER / SPEC Start /
	5. USER 2	Programming the [USER] key (press and holding)	Large Font/None
		assignment.
	1. APO	Selects the Auto Power Off time (time before power	Off / 0.5h / 1h / 8h
		goes off).
Setup	2. Emergency	Selects the Emergency feature.	121.5 / LED+121.5 / LED
	3. WX Alert	Selects the Alert functions when receiving the	Alrt Off / Beep / LED /
		Weather Alert Signal on the WX Channel.	Beep+LED
6. Misc
	4. TEMP Unit	Selects the measurement units for the Temperature	°F / °C
		sensor.
	5. TEMP Check	Enables/Disables the Over-Heating Alarm	Off / On
	6. TEMP Set	Program the threshold temperature for the “High-	[32.0 °F (0 °C)] -
		Temperature” indicator.	[230.0 °F (110 °C)]
Option	1. Internal MIC	Internal Microphone On/Off	Off / On
	2. TEMP Offset	Correcting the Thermometer setting	[–22.8 °F (–12.7 °C)] –
			[+22.8 °F (+12.7 °C)]
7.
	3. Clock Shift	CPU Clock Shift	Off / On

50

VXA-700 SPIRIT OPERATING MANUAL