Manuals / ViewSonic / Computer Equipment / Projector

ViewSonic PJD7382, PJD7400W warranty Resetting the lamp timer

Models: PJD7400 PJD7400W PJD7382

1 82

Download 82 pages 27.73 Kb

Page 63

Resetting the lamp timer

12.	Place the lamp protection film supplied
	with the new lamp on the lamp	2
	compartment.
13.	Replace the lamp cover on the	2
	projector.	2
	projector.
		1

14.Tighten the screws that secure the lamp cover.

CAUTION

•Loose screw may cause a bad connection,

which could result in malfunction.

• Do not over tighten the screws.

15.Restart the projector.

CAUTION

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

16.After the startup logo, open the On-Screen Display (OSD) menu.

17.Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press MODE/ENTER on the projector or ENTER on the remote control. The Lamp Settings page is displayed.

18.Press to highlight Reset lamp timer and press MODE/ENTER on the projector or ENTER on the remote control. A warning message is displayed asking if you want to reset the lamp timer.

19.Highlight Reset and press MODE/ENTER on the projector or ENTER on the remote control. The lamp time will be reset to '0'.

CAUTION

Do not reset if the lamp is not new or replaced as this could cause damage.

Notice

Reset Lamp Timer?

Reset Cancel

58

Image 63

ViewSonic PJD7382, PJD7400W warranty Resetting the lamp timer

Contents

User Guide PJD7382/PJD7400/PJD7400w DLP ProjectorFollowing information is only for EU-member states Compliance InformationFCC Statement For Canada CE Conformity for European CountriesImportant Safety Instructions Actual Concentration Declaration of RoHS ComplianceSubstance Proposed MaximumProduct Name Copyright InformationProduct Registration For Your RecordsTable of contents Important safetyPositioning your Safety Instructions Important safety instructions3. Refer servicing to qualified service personnel Safety instructions for ceiling mounting of the projector Do not cover this projector with a cloth or any other itemDo not place inflammables near the projector Introduction Projector featuresShipping contents Standard accessoriesOptional accessories Rear/lower side Projector exterior viewFront/upper side See Projector on page 8 forII POWER Controls and functionsProjector 4. POWER indicator light2. Source selection keys VGA 1/VGA 2/Video Remote control1. II POWER 10. Timer13. Laser Using the remote mouse control18. Volume keys + Operating the Laser pointerOperating the projector from the Remote control effective rangeReplacing the remote control batteries Operating the projector from the1. Front Table Positioning your projectorChoosing a location Set Rear Ceiling in the SYSTEM SETUP Basic169 image on a 43 screen Projection dimensionsPJD7382/PJD7400 PJD7382PJD7400 e Screen PJD7400w1610 image on a 1610 screen 1610 imageon a 43 screenConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorLeast video quality Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an S-Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to a Component Video source deviceAbout the microphone input Connecting a composite Video source devicePlaying sound through the projector To connect the projector to a composite Video source deviceSignal ParameterType Starting up the projector OperationSee Timing chart on page 64 for details SYSTEM SETUP Advanced Using the menusSETUP Basic menu SYSTEM SETUP BasicUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Switching input signal Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image claritySelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio PC input signals D-Sub / Comp. 1/2 analog RGB Optimizing the imageSelecting a picture mode Picture modes for different types of signalsAdjusting Brightness Using Screen ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessColor Management To adjust the settingsTo cancel the timer, perform the following steps Setting the presentation timerLocking control keys Hiding the imageFreezing the image Operating in a high altitude environmentTo activate the High Altitude Mode Creating your own startup screen If you are in a non-DHCP environment Controlling the projector through a LAN environmentConfiguring the LAN Control Settings If you are in a DHCP environmentControlling the projector through a web browser e-Con- trol Characters Category ItemInput Length Maximum Number ofPress Exit to go back to the remote network operation page Active VGA Out Using the projector in standby modePower Saving MicrophoneShutting down the projector Sub-menu Menu operationMenu system Main menuOptions 4. SYSTEM SETUP BasicMain menu Sub-menuMain menu SETUPSYSTEM AdvancedTI 3D DLP Link Description of each menupresentation. See Adjusting Brilliant Color on page 34 for image. See Adjusting Contrast on page 33 for detailsAdjusting Tint on page 34 for details Adjusting Sharpness on page 34 for detailswith one or more mirrors. See Choosing a location on page Using the menus on page 24 for detailsSee Using the projector in standby mode on page 44 for This function is only available when a PC source is in useClosed Caption Enable 5. SYSTEM SETUP Advanced menuVolume Microphone Volumeon how the total lamp hour is calculated See Getting to know the lamp hour on page 55 for detailsCare of the projector MaintenanceCleaning the lens Cleaning the projector caseSetting Lamp Mode as Economic Lamp informationGetting to know the lamp hour Extending lamp lifeSee Setting Lamp Mode as Economic on page Timing of replacing the lampType number RLC-057 PJD7382 Type number RLC-066 PJD7400/PJD7400w Replacing the lampPull out the lamp connector from a slot Resetting the lamp timer Powering up IndicatorsPower Power eventsNo picture TroubleshootingRemote control does not work The projector does not turn onProjector specifications Specifications149.5 DimensionsCeiling mount installation 254Supported timing for PC input Timing chartSupported timing for Video and S-Video inputs Supported timing for Component-YPbPr inputCopyright information CopyrightDisclaimer Pin assignment for this two end RS232 command tableAppendix IR control tableInterface Message Vertical 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F 0x06 0x14 0x00 0x04 0x00 0x34 0x15 T=Telephone Customer SupportCountry/Region Web SiteLimited One 1 year Heavy Usage Warranty Limited WarrantyWhat the warranty covers Limited Three 3 year General WarrantyHow to get service Limitation of implied warranties Exclusion of damagesEffect of state law Sales outside the U.S.A. and Canada Who the warranty protects What the warranty does not cover Mexico Limited WarrantyWhat the warranty covers How long the warranty is effectiveChihuahua, Chih NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO