Noise Reduction, Tnr Mnr Bar Off | ViewSonic VS11856 instruction

2-2-4 Noise Reduction

HQV technology reduces the irrelevant or noise data (Minimum loss of good data) from signal and creates better viewing quality.

Use ▲ and ▼ to navigate Selections of Noise Reduction Sub-Menu (Fig. 2-2-4).

Press to confirm the Sub-Menu selection.

Press to go to previous menu.

						ADVANCED
						OPERATION
	MNR	OFF	LOW	MEDIUM	HIGH	OPERATION
	MNR	OFF	LOW	MEDIUM	HIGH

Mosquito Noise Reduction: Reduce noise artifacts around object edges.

HQV-NR

ON

TNR 0

MNR 2

BAR

OFF

Fig. 2-2-4

Noise Reduction Sub-Menu

HQV-NR OFF ON

To turn On or Off HQV-noise reduction. HQV NR is a per- pixel motion & noise adaptive temporal filter.

TNR OFF LOW MEDIUM HIGH

Temporal Recursive Noise Reduction: Filter out the differences by comparing multiple image frames. This technique works best with still image.

Press ► to further reduce noise; press ◄ to restore the original state

Press ► to further reduce noise; press ◄ to restore the original state

BAR OFF ON

Block Artifact Removal: Remove block artifact caused by motion image processing.

Select ON to remove artifacts; OFF to restore the original state

ENG

27

Image 31

ViewSonic VS11856 user manual Noise Reduction, Tnr Mnr Bar Off

Contents

Precision by ViewSonic Compliance Information For Your Records Declaration of RoHS ComplianceCopyright Information Product Registration Introduction InstallationRemote Control Compliance Information Package Contents Projector FeaturesIntroduction Control Panel Projector Overview Color Temp Connection ports Remote ControlPower Menu ZOOM/FOCUS Input SelectLight Lens Shift Remote Control Operation Installing the Batteries Hdmi InstallationPower connection Audio and Video Devices Connectivity Configuration Installation Pro8100 RGB Adjusting the Projected Image Projection Screen Selection Adjusting Projection Image Size Power Light Remote Control direct accessOFF Zoom and Focus Lens Shift Picture Modes Aspect Ratio PCS OFF Color TemperaturePCS Precision Color System PCS on HQV OFF Black LevelHQV HQV on Input Select Daylight Sensor Direct Input Keys Remote Control direct access Advanced Operation OSD Menu Main Menu Setup Menu Basic Sub-Menu Picture Sub-Menu Position 75 Color Temperature Sub-Menu Image Adjust Sub-MenuPhase Position 71 Manual Overscan Keystone Geometry Adjust Advanced Sub-MenuAuto Auto V.KEYSTONE OFF LOW MID High Blacker than Black Picture Mode LTI OFF CTI 3 HQVEnhancement TNR MNR BAR OFF Noise Reduction RGB Color Space Config Sub-MenuAuto Projector Settings Location Timeout Transparency TypeTimeout 30 2 OSD Languages High Altitude Timers Auto Iris OFF Auto Iris PCS Settings Sub-Menu User 1 PCSPCS Display User PCS OFF Color Flesh tone Edge Enhancement Color Gamma Correction6 3D Color Management Green Enhance Blue Cyan Magenta Yellow Custom Color Memory Settings Sub-MenuLoad Green Gain Blue Gain RED Offset Green Offset Blue Offset Custom Color Temperature Load SaveLoad Save System Status Screen ResetMENU/EXIT Daylight sensor status Indication if System temperature status, display if system Making Adjustments User Picture Mode Adjustments Making and Recalling the User AdjustmentsUser Color Temperature Adjustments Recalling the User Picture Mode & Color Temperature User PCS Adjustments Recalling Both User Picture Mode and User PCS Custom 1 Recalling the User PCS Adjustments Making and Recalling the User Adjustments Appendix Replacing the Lamp Appendix List of Compatible Signals Troubleshooting WSXGA+ SXGA+Uxga Product Specification LED Indicator Message HDMI-1 RS232 command codeHDMI-2 Key-Pad & IR command Command Send String HEX Complete IR command code table Remote control code Country/Region Web Site =Telephone Mail =Fax Customer Support Limitation of implied warranties