Contents
ViewSonic
WPD-100 Wireless Presentation Dongle
User Guide
Model No. : VS13789
For U.S.A
Compliance Information
CE Conformity for European Countries
Following information is only for EU-memberstates
ViewSonic WPD-100
FCC Radiation Exposure Statement
R&TTE Compliance Statement
ViewSonic WPD-100
Declaration of RoHS Compliance
Product Registration
Copyright Information
For Your Records
Product Name
CHAPTER II: Driver Installation and Configuration
C A T A L O G
CHAPTER
Product Information
CHAPTER I: Product Information
1-1Introduction and safety information
1-2Safety Information
„Windows XP, Vista, or WIN7 operating system
1-3System Requirements
„CD-ROMdrive
„At least 100MB of available disk space
1- WPD-1001 pcs 2- Protection Cap 1 pcs
1-4Package Contents
3- Quick Start Guide 1 pcs
4- CD with Driver/Utility/User Manual 1 pcs
3 1 2 4
1-5Familiar with WPD-100
2-1 WPD-100Installation
CHAPTER II: Driver Installation and Configuration
4. It is recommend installing driver and utility. If you want to update the driver only, choose ’Install driver only’. Click ‘Next’ to continue
2-2Connect to Wireless Access Point
Menu Setup Area More / Less button
2-2-1Using WPD-100Utility
2-2-1-1Scan for Other Wireless Devices
Means this wireless device is an access point
EShows the bar graph of the signal strength
There are 4 types of technical information
Item Name
2-2-1-2Connect to an Access Point
Page
2-2-1-3Add an Access Point to Profile
Here are descriptions of every setup item
Power Save
Here are descriptions of every setup item
you selected. You can input 10 or 26 hexadecimal
credential file, click ‘Remove’
Here are descriptions of Profile List item
2-2-2Using Windows Zero Configuration
6.All wireless access points in proximity will be displayed here. If the access point you want to use is not displayed here, please try to move your computer closer to the access point, or you can click ‘Refresh network list’ to rescan access points. Click the access point you want to use if it’s shown, then click ‘Connect’
ViewSonic WPD-100
2-3Advanced Settings
2-4View Network Statistics
2-5WMM Setting
Item Name
2-6WPS Configuration
2-6-1WPS Setup - PBC Push-ButtonConfiguration
3.Start PBC pairing procedure at access point side please refer to the instruction given by your access point’s manufacturer, then click ‘PBC’ button in wireless configuration utility to start to establish wireless connection by WPS. Please be patient This may take a period to complete. When you see ‘WPS status is connected successfully’ message, means the connection between this wireless network card and access point is successfully established by WPS, and the information about access point you connected to will be displayed
2-6-2WPS Setup - PIN
2-7SSO
2-8CCX
2-10About
2-9Radio On/Off
ViewSonic WPD-100
2-11 On-lineHelp
Click this button to view on-linehelp documents
CHAPTER III: Soft-APFunction
3-1Switch to AP Mode and Basic Configuration
Item Name
permitted under FCC regulations
are in different country. For example: when
be operated. Selection of other channels is not
3-2Security Setting
data will not be encrypted and people with some
3-3Access Control
listed here to be connected to this access point
Here are descriptions of every field
3-4Connection Table
3-5Event Log
3-7About
3-6Statistics
ViewSonic WPD-100
3-8Open Diagnostic Testing Mode
ViewSonic WPD-100
CHAPTER IV: Appendix 4-1Specification
4-2Troubleshooting
an access point with encryption. Please
ViewSonic WPD-100
Customer Support
Country/Region
Website
ViewSonic WPD-100
Limited Warranty
