Contents
WPD-100 Wireless Presentation Dongle
ViewSonic
User Guide
Model No. : VS13789
Compliance Information
For U.S.A
CE Conformity for European Countries
Following information is only for EU-memberstates
FCC Radiation Exposure Statement
R&TTE Compliance Statement
ViewSonic WPD-100
Declaration of RoHS Compliance
ViewSonic WPD-100
Copyright Information
Product Registration
For Your Records
Product Name
C A T A L O G
CHAPTER II: Driver Installation and Configuration
CHAPTER
Product Information
1-1Introduction and safety information
CHAPTER I: Product Information
1-2Safety Information
1-3System Requirements
„Windows XP, Vista, or WIN7 operating system
„CD-ROMdrive
„At least 100MB of available disk space
1-4Package Contents
1- WPD-1001 pcs 2- Protection Cap 1 pcs
3- Quick Start Guide 1 pcs
4- CD with Driver/Utility/User Manual 1 pcs
1-5Familiar with WPD-100
3 1 2 4
CHAPTER II: Driver Installation and Configuration
2-1 WPD-100Installation
4. It is recommend installing driver and utility. If you want to update the driver only, choose ’Install driver only’. Click ‘Next’ to continue
2-2Connect to Wireless Access Point
2-2-1Using WPD-100Utility
Menu Setup Area More / Less button
2-2-1-1Scan for Other Wireless Devices
Means this wireless device is an access point
EShows the bar graph of the signal strength
There are 4 types of technical information
Item Name
2-2-1-2Connect to an Access Point
Page
2-2-1-3Add an Access Point to Profile
Here are descriptions of every setup item
Power Save
Here are descriptions of every setup item
you selected. You can input 10 or 26 hexadecimal
credential file, click ‘Remove’
Here are descriptions of Profile List item
2-2-2Using Windows Zero Configuration
6.All wireless access points in proximity will be displayed here. If the access point you want to use is not displayed here, please try to move your computer closer to the access point, or you can click ‘Refresh network list’ to rescan access points. Click the access point you want to use if it’s shown, then click ‘Connect’
ViewSonic WPD-100
2-3Advanced Settings
2-5WMM Setting
2-4View Network Statistics
Item Name
2-6WPS Configuration
2-6-1WPS Setup - PBC Push-ButtonConfiguration
3.Start PBC pairing procedure at access point side please refer to the instruction given by your access point’s manufacturer, then click ‘PBC’ button in wireless configuration utility to start to establish wireless connection by WPS. Please be patient This may take a period to complete. When you see ‘WPS status is connected successfully’ message, means the connection between this wireless network card and access point is successfully established by WPS, and the information about access point you connected to will be displayed
2-6-2WPS Setup - PIN
2-7SSO
2-8CCX
2-9Radio On/Off
2-10About
2-11 On-lineHelp
Click this button to view on-linehelp documents
ViewSonic WPD-100
3-1Switch to AP Mode and Basic Configuration
CHAPTER III: Soft-APFunction
Item Name
are in different country. For example: when
be operated. Selection of other channels is not
permitted under FCC regulations
3-2Security Setting
data will not be encrypted and people with some
3-3Access Control
listed here to be connected to this access point
3-4Connection Table
Here are descriptions of every field
3-5Event Log
3-6Statistics
3-7About
3-8Open Diagnostic Testing Mode
ViewSonic WPD-100
CHAPTER IV: Appendix 4-1Specification
ViewSonic WPD-100
4-2Troubleshooting
an access point with encryption. Please
Customer Support
ViewSonic WPD-100
Country/Region
Website
Limited Warranty
ViewSonic WPD-100
