Leveling ALL Steamers & Steam Generators

LEVELING — ALL STEAMERS & STEAM GENERATORS

Position the steamer or steam generator in its final installed location. Place a level on the horizontal area of the cabinet. Adjust the feet to level the steamer or steam generator in both the left-to-right and front-to-rear directions.

On VHX steamers only, elevate the front 1/16" to 1/8" (0.2 cm to 0.3 cm) to give proper drainage by rotating the adjusting nut on the rear legs in the proper direction 1 to 11/2 turns. Check drainage in the steamer compartments by pouring a little water in the compartment. All the water should drain. On VHL steamers only, elevate the right side legs 1/16" to 1/8" (0.2 cm to 0.3 cm) to give proper drainage.

The rear feet have holes in the flanges for anchor bolts. Direct steam models (steamers without generators) must be anchored to the floor.

PLUMBING CONNECTIONS — ALL STEAMERS & STEAM GENERATORS

WARNING: PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY AND PLUMBING CODES.

Water Requirements

Proper water quality can improve the taste of the food prepared in the steamer, reduce liming in the steam generator and extend equipment life. Local water conditions vary from one location to another. Ask your municipal water supplier for details about your local water supply prior to installation.

WATER REQUIREMENTS

Supply Pressure	20 — 60 psig
Hardness*	less than 3 grains
Silica	less than 13 ppm
Total Chlorine	less than 4.0 ppm
pH range	7 — 8
Undissolved Solids	less than 5 microns

*17.1 ppm = 1 grain of hardness

Presence of sediment, silica, excess chlorides or other dissolved solids may lead to a recommendation for alternate form(s) of water treatment. Test the water with the test strip included with the steamer. Other factors affecting steam generation are iron content, amount of chloridation and dissolved gases. A local water treatment specialist should be consulted before installation of steam generating equipment.

Water Supply Connection

Connect the treated water supply line to the 1/2" NPT (1.3 cm) inlet at the rear of the steamer. Connect the untreated water supply line to the 1/4" (0.6 cm) copper tube inlet, also at the rear of the steamer.

A water filter system is recommended for the water supply line going to the treated water inlet of your steamer. Follow the recommendations for use and installation instructions shipped with the water filter. If a water filter is not installed, the steamer or steam generator warranty may be limited.

Drain Connection

The 11/4" NPT (3.175 cm) threaded fitting on the condenser box must be extended a maximum of 12" (30.5 cm) to an open air gap type drain. Do not reduce the 11/4" (3.175 cm) drain piping throughout its length. Provide a suitable floor sink with a minimum depth of 12" (30.5 cm). The floor sink is NOT to be directly under the steamer and should be at a distance so that steam vapors will not enter the steamer from underneath. The drain pipe should be either iron or copper. DO NOT use PVC pipe; PVC pipe may lose its rigidity or glue may fail.

CAUTION: In order to avoid any back pressure in the steamer, do not connect solidly to any drain connection.

– 6 –

VHL3 & VH3616, VHL2, VHX24 specifications

Vulcan-Hart is renowned for its high-quality commercial cooking equipment, particularly in the foodservice industry. The VHX24, VHL2, VHL3, and VH3616 are standout models in their lineup, each offering unique features and technologies designed to meet the diverse needs of restaurants, cafeterias, and other food preparation settings.

The Vulcan-Hart VHX24 is a powerful countertop convection oven that emphasizes efficiency and versatility. With a diverse cooking capacity, it can handle a variety of dishes simultaneously. It features a digital control panel that allows for precise temperature settings and cooking times, making it easier for chefs to achieve consistent results. This model also includes a stainless-steel exterior for easy cleaning and durability, making it a reliable choice in busy kitchens.

Moving on to the VHL2, this heavy-duty gas-fired broiler is engineered for high-volume grilling. It boasts dual burners that provide uniform heat distribution, ensuring that meat and vegetables are cooked evenly and to perfection. The VHL2 is also designed with a removable grease drawer, making maintenance straightforward and efficient. Its robust construction and large cooking surface make it an ideal choice for establishments that require extensive grilling capabilities.

The VHL3 takes the broiling experience a step further. This model includes three burners for enhanced cooking flexibility, allowing chefs to prepare larger quantities of food without sacrificing timing or quality. The VHL3 also features an adjustable grid and a high-efficiency radiant system, which reduces energy consumption while maintaining exceptional cooking performance. It’s perfect for busy kitchens that do not compromise on quality.

Finally, the VH3616 is a versatile, heavy-duty gas countertop fryer equipped to handle high-volume frying needs. It has a sizeable fry pot, making it suitable for cooking large batches of fries, chicken, and more. The VH3616 features a state-of-the-art temperature control system that ensures oil heats quickly and maintains consistent temperatures for optimal cooking results. Additionally, it includes a built-in filtration system that helps prolong the life of the oil and enhances food quality.

Together, the Vulcan-Hart VHX24, VHL2, VHL3, and VH3616 exemplify the brand's dedication to quality, innovation, and user-friendly design. Each model is tailored to support the demanding environments of commercial kitchens, providing chefs with the tools they need to create exceptional meals efficiently and consistently. Whether it’s baking, broiling, or frying, Vulcan-Hart continues to deliver reliable equipment that exceeds industry standards.

Vulcan-Hart VHX24, VHL2 Leveling ALL Steamers & Steam Generators, Water Requirements

Models: VHL3 & VH3616 VHL2 VHX24