MAINTENANCE
MAINTENANCE
INSTRUCTIONS
1)Always shut the valve off before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean brush as the logs are fragile and easily damaged.
2)Clean glass (never when unit is hot), appli- ance, and door with a damp cloth. Never use an abrasive cleaner.
3)The heater is finished in a porcelain finish or with a heat resistant paint and should only be refinished with heat resistant paint (not with wall paint). Waterford uses Stove- Bright Paint - Metallic Black #6309.
Never use an abrasive cleaner on the por- celain finish as it may scratch the surface.
4)Make a periodic check of burner for proper position and condition. Visually check the flame of the burner periodically, making sure the flames are steady; not lifting or floating. If there is a problem, call a qualified service person.
5)The appliance and venting system must be inspected before use, and at least annually, by a qualified field service person, to en- sure that the flow of combustion and ven- tilation air is not obstructed.
During the annual service call, the burner should be removed from the burner tray and cleaned. Replace the embers - do not block the pilot or burner ports.
6)Keep the area near the appliance clear and free from combustible materials, gasoline and other flammable vapours and liquids.
CAUTION: ANY SAFETY SCREEN ORGUARDREMOVEDFORSERV- ICING AN APPLIANCE MUST BE REPLACED PRIOR TO OPERAT- ING THE APPLIANCE.
WARNING: CHILDREN AND ADULTSSHOULDBEALERTEDTO THEHAZARDSOFHIGHSURFACE TEMPERATURE AND SHOULD STAYAWAYTOAVOIDBURNSOR CLOTHING IGNITION. YOUNG CHILDRENSHOULDBECAREFUL- LYSUPERVISEDWHENTHEYARE IN THE SAME ROOM AS THE AP- PLIANCE.
CLOTHING OR OTHER FLAMMA- BLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLI- ANCE.
DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN UNDER WA- TER.IMMEDIATELYCALLAQUAL- IFIED SERVICE TECHNICIAN TO INSPECTTHEAPPLIANCEANDTO REPLACEANYPARTOFCONTROL SYSTEMANDANYGASCONTROL WHICHHASBEENUNDERWATER.
7)Verify proper operation after servicing.
PILOT ADJUSTMENT
Periodically check the pilot flames. Correct flame pattern has three strong blue flames: 1 flowing around the thermopile and 1 around the thermocouple, and 1 flowing across the rear of the burner (it does not have to be touching the burner).
Note: If you have an incorrect flame pat- tern, contact your Waterford deal- er for further instructions.
Top View of pilot flame
Incorrect flame pattern will have small, prob- ably yellow flames, not coming into proper contact with the rear of the burner or thermo- pile.
Top View of pilot flame
LOG REPLACEMENT
The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door to carefully remove the logs. The pilot light generates enough heat to burn someone. If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the diagram under Log Installation.
Note: Improper positioning of logs may create carbon
GLASS
REPLACEMENT
Your EMERALD stove is supplied with high temperature, 5 mm Neoceram ceramic glass that will withstand the highest heat that your unit will produce. In the event that you break your glass by impact, purchase your replace- ment door from an authorized Waterford dealer only, and follow our
1)Open the front door. Open the right side door and there is a cutout in the heat shield through which can be seen a wing nut threaded on to a stud attached to the front door. Loosen this nut by turning it counter- clockwise.
The wing nut that holds the front door is accessible through the
2)Remove the six screws that secure the retainers holding the glass in place.
3)Remove the glass and replace with the new glass.
4)Install two bottom retainers and turn the screws in just enough to support the glass.
5)Install the other retainers, tighten the screws alternately. Do not overtighten as this can damage the glass.
6)Close the door. Thread the nut onto the end of the stud.
Waterford | 17 |
