|
| |
13 | Torsion End Bearing Brackets | |
Tools Needed: | End bearing brackets are right and left | |
Step Ladder | hand. Break the end bearing brackets | |
Power Drill | apart. | |
Starting on the left hand side and using | ||
| ||
Ratchet Wrench | the upper slots in the end bearing | |
7/16” Socket | bracket, position above the flagangle | |
and secure the end bearing bracket to | ||
Driver | ||
the horizontal angle using (2) | ||
| ||
9/16” Socket | x 3/4” truss head bolts and (2) | |
Driver | nuts. | |
| IMPORTANT: END BEARING BRACKETS |
Right hand end bearing bracket
Break
the end bearing brackets apart
Left hand end bearing
bracket
UPPER SLOTS
USED ON 15”
RADIUS TRACK.
LOWER SLOTS
ON 12” RADIUS
TRACK.
Horizontal angle
9/16” Wrench | MUST BE ATTACHED THROUGH THE |
| |
| LOWER SLOTS ON 12” RADIUS TRACK. |
| 15” RADIUS TRACK MUST USE THE UP- |
| PER SLOTS ON THE BRACKET. |
| Once the bracket is secured to the |
| horizontal angle, secure the top of the |
| end bearing bracket to the jamb using |
| (1) 5/16” x |
| right hand side. |
| NOTE: Right and left hand is always |
| determined from inside the building |
| looking out. |
Left hand | (1) 5/16” x |
end bearing | lag screw |
bracket |
|
(2)
Horizontal
angle
(2)
INSTALLATION
14 |
| Center of | Vertical line |
|
|
|
| ||
| Center Bearing Bracket | end bearing |
| |
|
|
| ||
| bracket |
|
| |
|
|
|
| |
Tools Needed: | Measure to locate the center of the door and mark |
| Horizontal line |
|
a vertical pencil line on the mounting surface above |
|
|
| |
Power Drill |
|
| Center | |
the door, to indicate the center line of the door. Then, |
|
| ||
7/16” Socket Driver |
|
| bearing | |
measure from the center of the bearing, in one of |
|
| ||
Level |
|
| bracket | |
the end bearing brackets, DOWN to the top of the |
|
| ||
Tape Measure |
|
|
| |
door. Using that dimension, measure UP from the top |
|
|
| |
Pencil |
|
|
| |
of the door and mark a horizontal pencil line on the |
|
|
| |
1/4” Torx Bit |
|
|
| |
mounting surface, intersecting the vertical pencil line. |
|
|
| |
Step Ladder |
|
|
| |
Now align the edge of the center bearing bracket |
|
|
| |
|
|
|
| |
| along the vertical pencil line on the mounting surface. |
|
|
|
| Center the bearing bracket on the horizontal line. |
|
|
|
| This will ensure the torsion tube is level between the |
|
|
|
| center and end bearing brackets. Attach the center |
|
|
|
| bearing bracket, in this location, to the mounting |
| Vertical | Center |
| surface, using (2) 5/16” x |
| ||
|
| line | bearing | |
| 5/16” x 2” |
| ||
|
|
| bracket | |
|
|
|
| |
| Important: Use the 5/16” x 1 5/8” tamper- |
|
|
|
| resistant lag screw only if mounting surface |
|
|
|
| mounted over masonry. |
|
|
|
| screw must be attached through the bottom |
|
|
|
| hole of the center bearing bracket. |
|
| (2) 5/16” X 2” |
|
|
|
| |
|
|
|
| Lag screws |
|
|
| Horizontal |
|
|
|
| line |
|
|
|
|
| (1) 5/16” X |
|
|
|
| screw or (1) 5/16” x 2” |
|
|
|
| |
|
|
|
| screw |
15
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at