41. Identify the Ab Cable (83); it is approximately | 41 |
|
|
|
|
|
220.25” long and it has a ball on one end and a |
|
|
|
|
| |
|
|
|
|
|
| |
loop on the other. | 91 | 75 |
|
|
| Large tabs |
|
|
|
| must be on | ||
Wrap the Ab Cable (83) around a 3 1/2” Pulley |
|
|
|
|
| |
|
|
|
| 49 | this side | |
(37). Place two Pulley Covers (49) over the |
|
|
|
| 37 | |
Pulley; make sure that the large tabs are in the | Rod |
|
| |||
|
|
|
| |||
position shown. Attach the Pulley and Pulley |
|
|
|
|
|
|
Covers to the Butterfly Upright (4) with a 3/8” x 4” |
|
|
|
|
|
|
Bolt (91), two 3/8” Washers (75), and a 3/8” Nylon |
|
| Ball | 83 | 75 |
|
Locknut (74). Be sure that the Cable is between |
|
|
| 74 | ||
4 |
|
| 49 | |||
the Pulley and the rod on the Upright, and that |
|
|
|
|
| |
the ball is on the side shown. |
|
|
|
|
|
|
42. Remove the two 3 1/2” Pulleys (37) from the | 42 |
|
|
|
|
|
Double |
|
|
|
|
| |
|
|
|
|
|
| |
around a Pulley. Reattach the Pulley to the | 83 |
|
|
|
|
|
Double |
|
|
|
|
| |
|
|
|
|
|
| |
3/8” Nylon Locknut (74). |
|
|
|
|
|
|
| 37 |
|
|
|
|
|
| 74 |
|
|
|
|
|
| 42 | 79 |
|
|
| |
43. Wrap the Ab Cable (83) around the other 3 1/2” | 43 |
|
|
|
|
|
Pulley (37) removed in step 38. Reattach the |
|
|
|
|
| |
|
|
|
|
|
| |
Pulley and Cable Trap (44) to the bottom set of |
|
|
|
|
|
|
holes in the Pulley Plates (43) with the 3/8” x 2” |
|
|
| 43 |
| |
Bolt (79) and the 3/8” Nylon Locknut (74). Be |
|
|
|
| ||
sure the Cable Trap is turned to hold the |
| 79 |
|
| 74 |
|
Cable in the groove of the Pulley. |
|
|
|
| ||
|
|
|
|
| ||
|
|
|
|
| 44 |
|
|
| 83 |
| 37 |
|
|
44. Wrap the Ab Cable (83) around a 3 1/2” Pulley | 44 |
|
|
|
|
|
(37). Attach the Pulley and a Cable Trap (44) to |
|
|
|
|
| |
|
|
|
|
|
| |
the Butterfly Base (1) with a 3/8” x 1 3/4” Bolt | 83 |
|
|
|
|
|
(103) and a 3/8” Nylon Jamnut (88). Make sure | 103 |
|
|
|
|
|
the Cable Trap is oriented as shown. |
|
|
|
|
| |
|
|
|
|
|
| |
|
| 44 | 1 |
|
|
|
|
|
|
|
|
| |
| 37 |
|
|
|
|
|
|
|
| 88 |
|
|
|
| 17 |
|
|
|
|
|
