56. Press a 1 1/2” Square Inner Cap (100) into the | 56 |
|
|
|
back of the Backrest Bracket (21). Press two 1” x |
|
|
| |
|
| 98 |
| |
2” Inner Caps (70) into the top and bottom of the |
|
|
| |
| 70 |
|
| |
Backrest Bracket. |
|
|
| |
|
|
|
| |
Insert a 1/4” x 1 3/4” Carriage Bolt (93) into the |
|
| 84 |
|
| 21 |
|
| |
center hole of a Support Plate (57). Attach the |
| 100 |
| |
Support Plate to Press Backrest (20) with two |
|
|
|
|
1/4” x 3/4” Screws (90). Attach the Backrest to |
| 90 | 106 | 51 |
the Backrest Bracket (21) with the Carriage Bolt, |
| 57 |
| |
20 |
|
| ||
a 1/4” Washer (84), and a 1/4” Nylon Locknut |
|
|
| |
|
| 84 |
| |
(106). Attach the top of the Backrest to the |
|
| 6 | |
Backrest Bracket with 1/4” x 1 3/4” Screw (98) |
|
| 90 |
|
and a 1/4” Washer (84). |
| 93 |
|
|
|
|
|
| |
Loosen the Adjustment Knob (51) by turning it |
| 70 |
|
|
|
|
|
| |
counterclockwise, and pull it out as far as possi- |
|
|
|
|
ble. Insert the Backrest Bracket (21) into the |
|
|
|
|
Press Upright (6) and align an adjustment hole |
|
|
|
|
with the the Adjustment Knob. Snap the Knob into |
|
|
|
|
the adjustment hole and turn it clockwise until | 57 |
|
|
|
tight. |
|
|
| |
|
|
|
| |
57. Press a 1 3/4” Square Inner Cap (60) into the |
| 46 |
|
|
|
| 23 | 60 | |
back of the Adjustment Tube (23). |
|
| ||
| 66 |
| ||
|
|
|
| |
Attach the Adjustment Tube (23) to the Press |
| 64 |
|
|
|
|
|
| |
Plate (24) with a 5/16” x 2 1/2” Bolt (63), two |
|
|
|
|
5/16” Washers (66), and a 5/16” Nylon Locknut |
|
|
|
|
(64). |
|
| 66 |
|
|
|
| 63 |
|
Attach the Adjustment Tube (23) to the Leg Press |
|
|
|
|
Arm (22) with the Press Pin (46). |
| 24 |
|
|
|
| 22 |
| |
|
|
|
| |
58. Press four 3/4” Round Inner Caps (73) into the | 58 |
|
|
|
ends of the Long and Short Pad Tube (39, 40). |
|
|
| |
73 |
|
|
| |
| 41 |
|
| |
Insert the Long Pad Tube (39) into the welded |
|
|
| |
|
|
|
| |
tube on the Butterfly Front Leg (9). Slide two |
|
|
|
|
Foam Pads (41) onto the ends of the Pad Tube. |
| Welded |
|
|
| 73 |
|
| |
Insert the Short Pad Tube (40) into the hole in the | Tube |
|
| |
|
|
| ||
Leg Lever (8). Slide two Foam Pads (41) onto the |
| 39 |
|
|
ends of the Pad Tube |
|
|
| |
|
|
| 41 | |
| 41 |
|
| |
| 8 |
|
| |
|
|
|
| |
|
|
|
| 73 |
|
| 40 |
|
|
|
| 9 |
|
|
|
|
| 41 | 73 |
|
|
|
|
21
