Manuals
/
Weider
/
Fitness & Sports
/
Home Gym
Weider
831.159530 user manual Remove This Part List/Exploded Drawing From The Manual
Models:
831.159530
1
33
35
35
Download
35 pages
47.75 Kb
28
29
30
31
32
33
34
35
<
>
Cable Diagrams
Replacement Parts
Assembly
back of the Adjustment Tube
Weight
Page 33
Image 33
REMOVE THIS PART LIST/EXPLODED
DRAWING FROM THE MANUAL
Page 32
Page 34
Page 33
Image 33
Page 32
Page 34
Contents
Visit our website at
USER’S MANUAL
new products, prizes fitness tips, and much more
Model No Serial No
TABLE OF CONTENTS
the accompanying literature before using the
IMPORTANT PRECAUTIONS
weight system
that all users of the weight system are ade
Decal
BEFORE YOU BEGIN
Decal
Decal
ASSEMBLY
Frame Assembly
Locate and open the parts bags labeled “FRAME ASSEMBLY 1 and 2.”
64. Do not tighten the Nylon Locknuts yet
Do not tighten the 3/8” Nylon Locknuts 74 yet
Do not tighten the Nylon Locknuts 64, 74 yet
are near the top of the Weight Carriages
Weight Guides 33. Be sure the weight tubes
shown, and that it rests between the Weight
74. Note Be sure that the Top Frame is ori
Nylon Locknut the Pulley must be able to turn easily
11. Press a 2” Square Inner Cap 59 into the Press Top Frame
Do not tighten the Nylon Locknuts 64, 74 yet
Do not tighten the 5/16” Nylon Locknuts 64 yet
ASSEMBLY.”
Arm Assembly
15. Locate and open the parts bag labeled “ARM
indicated axle. Be sure the upper end of the
Nylon Locknut 74. Do not overtighten the
Nylon Locknut the Press Frame must be able
to pivot easily
Cable Assembly
Page
Trap is oriented as shown
Bracket
Bracket
Bracket
Cable Trap is turned to hold the Cable in the groove of the Pulley
Cable Trap is turned to hold the Cable in the groove of the Pulley
Locknut 74. Be sure that the Cable is between
Pulley make sure that the large tabs are in the
the Pulley and the rod on the Upright, and that
the ball is on the side shown
Locknut 74. Make sure the Cable Trap is ori
ented to hold the Cable in the groove of the
Pulley
Page
53. Locate and open the parts bag labeled “SEAT ASSEMBLY.”
Seat Assembly
Press Upright 6 and align an adjustment hole
Loosen the Adjustment Knob 51 by turning it
with the the Adjustment Knob. Snap the Knob into
the adjustment hole and turn it clockwise until
Page
ADJUSTING THE SEAT
ADJUSTMENTS
ADJUSTING THE PRESS BACKREST
ADJUSTING THE PRESS PLATE
USING THE WEIGHT CARRIAGE
ATTACHING THE CURL PAD
ATTACHING THE LAT BAR
Weight
WEIGHT RESISTANCE CHART
High
Butterfly
Cable ID Chart
CABLE DIAGRAMS
Butterfly Cable
Ab Cable
TIGHTENING THE CABLES
TROUBLE-SHOOTING AND MAINTENANCE
REPLACEMENT PARTS
FULL 90 DAY WARRANTY
a part is missing or you need to schedule repair service
QUESTIONS?
REMOVE THIS PART IDENTIFICATION CHART FROM THE MANUAL
1 1/2 Square Inner Cap 1 1/2 Round Inner Cap 1 CoverCap
1 3/4 Square Inner Cap 2 Square Inner Cap 1 x 2” Inner Cap
1” Retainer
3/4 Round Inner Cap
1/4 x 3/4 Screw 1/2 Nylon Locknut Bumper Screw 3/8 Nylon Locknut
PART LIST-Model No
3/8 Nylon Jamnut 5/16 Nylon Locknut 5/16 Nylon Jamnut
1/4 Nylon Locknut
5/16 x 2 1/2 Carriage Bolt 3/8 x 2 1/2 Carriage Bolt
3/8 Washer 3/8 SAE Washer 5/16 Washer 1/4 Washer
5/16 x 2 3/4 Bolt 3/8 x 2 3/4 Bolt 3/8 x 3 1/4 Bolt 3/8 x 3 1/2 Bolt
1/2 x 3 1/2 Bolt 3/8 x 3 3/4 Bolt 3/8 x 4 Bolt 3/8 x 4 1/4 Bolt
REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL
Description
PART LIST-Model No
Key No. Qty
Description
R1001A
2730
EXPLODED DRAWING-Model No