Manuals / Weider / Fitness & Sports / Home Gym

Weider 831.159530 user manual Remove This Part Identification Chart From The Manual

Models: 831.159530

1 35

Download 35 pages 47.75 Kb

Page 29

Image 29

REMOVE THIS PART IDENTIFICATION

CHART FROM THE MANUAL

This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part from the PART LIST in the center of this manual. Important:

Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled.

Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable assembly; and 4) seat assembly. The hardware for each assembly stage is packaged separately. Wait until you begin each stage to open that parts bag.

Page 29

Image 29

Weider 831.159530 user manual Remove This Part Identification Chart From The Manual

Contents

Visit our website at USER’S MANUALnew products, prizes fitness tips, and much more Model No Serial NoTABLE OF CONTENTS the accompanying literature before using the IMPORTANT PRECAUTIONSweight system that all users of the weight system are adeDecal BEFORE YOU BEGINDecal DecalASSEMBLY 64. Do not tighten the Nylon Locknuts yet Frame AssemblyLocate and open the parts bags labeled “FRAME ASSEMBLY 1 and 2.” Do not tighten the 3/8” Nylon Locknuts 74 yet Do not tighten the Nylon Locknuts 64, 74 yetare near the top of the Weight Carriages Weight Guides 33. Be sure the weight tubesshown, and that it rests between the Weight 74. Note Be sure that the Top Frame is oriNylon Locknut the Pulley must be able to turn easily 11. Press a 2” Square Inner Cap 59 into the Press Top FrameDo not tighten the Nylon Locknuts 64, 74 yet Do not tighten the 5/16” Nylon Locknuts 64 yetASSEMBLY.” Arm Assembly15. Locate and open the parts bag labeled “ARM indicated axle. Be sure the upper end of theto pivot easily Nylon Locknut 74. Do not overtighten theNylon Locknut the Press Frame must be able Cable Assembly Page Trap is oriented as shown Bracket BracketBracket Cable Trap is turned to hold the Cable in the groove of the Pulley Cable Trap is turned to hold the Cable in the groove of the PulleyLocknut 74. Be sure that the Cable is between Pulley make sure that the large tabs are in thethe Pulley and the rod on the Upright, and that the ball is on the side shownPulley Locknut 74. Make sure the Cable Trap is oriented to hold the Cable in the groove of the Page 53. Locate and open the parts bag labeled “SEAT ASSEMBLY.” Seat AssemblyPress Upright 6 and align an adjustment hole Loosen the Adjustment Knob 51 by turning itwith the the Adjustment Knob. Snap the Knob into the adjustment hole and turn it clockwise untilPage ADJUSTING THE SEAT ADJUSTMENTSADJUSTING THE PRESS BACKREST ADJUSTING THE PRESS PLATEATTACHING THE LAT BAR USING THE WEIGHT CARRIAGEATTACHING THE CURL PAD Weight WEIGHT RESISTANCE CHARTHigh ButterflyCable ID Chart CABLE DIAGRAMSButterfly Cable Ab CableTIGHTENING THE CABLES TROUBLE-SHOOTING AND MAINTENANCEREPLACEMENT PARTS FULL 90 DAY WARRANTYa part is missing or you need to schedule repair service QUESTIONS?REMOVE THIS PART IDENTIFICATION CHART FROM THE MANUAL 1 1/2 Square Inner Cap 1 1/2 Round Inner Cap 1 CoverCap 1 3/4 Square Inner Cap 2 Square Inner Cap 1 x 2” Inner Cap1” Retainer 3/4 Round Inner Cap1/4 x 3/4 Screw 1/2 Nylon Locknut Bumper Screw 3/8 Nylon Locknut PART LIST-Model No3/8 Nylon Jamnut 5/16 Nylon Locknut 5/16 Nylon Jamnut 1/4 Nylon Locknut5/16 x 2 1/2 Carriage Bolt 3/8 x 2 1/2 Carriage Bolt 3/8 Washer 3/8 SAE Washer 5/16 Washer 1/4 Washer5/16 x 2 3/4 Bolt 3/8 x 2 3/4 Bolt 3/8 x 3 1/4 Bolt 3/8 x 3 1/2 Bolt 1/2 x 3 1/2 Bolt 3/8 x 3 3/4 Bolt 3/8 x 4 Bolt 3/8 x 4 1/4 BoltREMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL Description PART LIST-Model NoKey No. Qty DescriptionEXPLODED DRAWING-Model No R1001A2730