61. Attach the Press Cable (72) to the remaining “U”- | 61 |
|
|
|
|
Bracket (33) with a 1/4” Washer (99) and a 1/4” |
|
|
|
| |
|
|
|
|
| |
Nylon Locknut (103). Note: Do not completely | 72 |
|
|
| |
tighten the Nylon Locknut; it should be |
| 96 |
| ||
threaded only two turns onto the end of the |
|
| 33 |
| |
|
|
|
| ||
Cable, as shown in the inset drawing. | 86 |
| 99 |
| |
| 43 |
|
| ||
Attach the |
| 103 |
| ||
|
| 72 | |||
Tube (43) with a 5/16” x 1 3/4” Bolt (96) and a |
|
|
|
| |
|
|
|
|
| |
5/16” Nylon Locknut (86). |
|
|
|
|
|
Important: Follow all five cables from end to |
|
|
|
|
|
end and make sure that they rest in the |
|
|
|
| 103 |
grooves of all of the pulleys and that the |
|
|
|
|
|
cables and the pulleys move smoothly. |
|
|
|
|
|
Seat Assembly | 62 |
|
|
|
|
|
|
|
|
| |
62. Locate and open the parts bag labeled “SEAT | 25 |
| 99 | 79 |
|
ASSEMBLY.” |
|
|
| ||
|
|
|
| ||
Attach the Butterfly Backrest (25) to the Butterfly |
|
| 4 |
|
|
|
|
|
|
| |
Upright (4) with two 1/4” x 2 1/2” Bolts (79) and |
|
|
|
|
|
two 1/4” Washers (99). |
|
|
| 79 |
|
|
|
|
|
| |
|
|
| 99 |
|
|
63. Insert a 1/4” x 2 1/2” Carriage Bolt (91) through | 63 |
|
|
|
|
the center hole in a Seat Plate (30). Attach the |
|
|
|
| |
23 |
|
|
|
| |
Seat Plate to a Seat (23) with two 1/4” x 3/4” Bolt |
|
|
|
|
|
(98). |
|
|
|
|
|
Insert the 1/4” x 2 1/2” Carriage Bolt (91) into the |
|
| 91 |
|
|
indicated hole in the Butterfly Seat Frame (10) |
|
| 30 |
|
|
and secure it with a 1/4” Washer (99) and a 1/4” |
|
|
|
| |
|
|
|
|
| |
Nylon Locknut (103). Secure the other end of the |
|
| 98 |
|
|
Seat (23) with a 1/4” x 2 1/2” Bolt (79) and a 1/4” |
|
|
|
| |
|
|
|
|
| |
Washer. |
|
|
|
|
|
Attach the other Seat (23) to the Press Seat |
|
| 99 |
|
|
Frame (12, not shown) in the same manner. |
|
| 103 |
|
|
|
|
| 79 |
|
|
64. Insert a 1/4” x 2 1/2” Carriage Bolt (91) through | 64 |
|
|
|
|
the center hole in a Seat Plate (30). Attach the |
|
|
|
| |
|
|
|
| 79 | |
Seat Plate to the Press Backrest (24) with two |
|
|
|
| |
|
|
|
| 99 | |
1/4” x 3/4” Bolt (98). |
|
|
|
| |
24 |
|
| 5 |
| |
|
|
|
| ||
|
|
|
|
| |
Insert the 1/4” x 2 1/2” Carriage Bolt (91) into the |
|
|
|
|
|
indicated hole in the Press Upright (5) and secure |
|
|
|
| 103 |
it with a 1/4” Washer (99) and a 1/4” Nylon |
|
| 98 |
| |
30 |
|
| 99 | ||
Locknut (103). Secure the other end of the Press |
|
|
|
|
|
Backrest (24) with a 1/4” x 2 1/2” Bolt (79) and |
|
|
|
|
|
another 1/4” Washer. |
| 91 |
|
| |
|
|
|
| ||
| 23 |
|
|
|
|
