Manuals / Weider / Fitness & Sports / Home Gym

Weider 831.159830 user manual Locknuts yet

Models: 831.159830

1 39

Download 39 pages 51.17 Kb

Page 7

Locknuts yet.

4.Slide the Butterfly Upright (4) over the indicated 5/16” x 2 1/2” Carriage Bolts (75) in the Butterfly Base (1). Hand tighten two 5/16” Nylon Locknuts (86) onto the Bolts. Do not tighten the Nylon

Locknuts yet.

5.Press three 2” Square Inner Caps (67) into the Butterfly Top Frame (7). Press two Round Inner Caps (63) into the top of the Butterfly Top Frame.

Attach the Butterfly Top Frame (7) to the indicat- ed bracket at the top of the Butterfly Upright (4) with two 5/16” x 2 3/4” Bolts (89), a Medium Support Plate (109), and two 5/16” Nylon Locknuts (86).

6.Press a 2” Square Inner Cap (67) halfway into the top of the Butterfly Leg (11). Attach a Bumper (50) to the Butterfly Leg with a 1” Tap Screw (80).

Attach the Butterfly Seat Frame (10) to the Butterfly Leg (11) with two 5/16” x 2 3/4” Bolts (89), two 5/16” Washers (100), and two 5/16” Nylon Locknuts (86). Do not tighten the Nylon

Locknuts yet.

4
			4
			86
			86
			1
			75
5			89
			89
			109
			63
	67		67
	67
		7	63
		7
			67
			86
			4
6			67
			67
			86
	100		10
89			86
89
	100
80	50		11
80

7

Image 7

Weider 831.159830 user manual Locknuts yet

Contents

USER’S MANUAL Visit our website atnew products, prizes fitness tips, and much more TABLE OF CONTENTS IMPORTANT PRECAUTIONS BEFORE YOU BEGIN ASSEMBLY Locate and open the parts bag labeled “FRAME ASSEMBLY.” Frame AssemblyLocknuts yet Locknuts yetATTACHING THE CURL PAD ADJUSTMENTSATTACHING THE ACCESSORIES TO A PULLEY STATION ADJUSTING THE LEG PRESS PLATEDo not tighten the Nylon Locknuts yet Guides 26. Make sure the Weights are turned Note The tops of the four Weight Guides Arm Assembly Cable Assembly 90. Make sure the Long Cable Trap is orient 26. Remove another “V”-Pulley 34 from the baglabeled “PULLEY BAG 2.” on the back of the Butterfly Upright 4 with aJamnut 92. Make sure the Cable is between Trap is positioned to hold the Cable in thegroove of the Pulley 32. Identify the Ab Cable 74. It is approximatelygroove of the Pulley Trap is positioned to hold the Cable in thegroove of the Pulley Trap is positioned to hold the Cable in theLocknut 90. Make sure the Cable is routed in 42. Remove a Pro Pulley 110 from the bag labeled “PULLEY BAG 2.” 47. Remove a Pro Pulley 110 from the bag labeled “PULLEY BAG 2.” Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley 53. Wrap the Press Cable 72 around a 3 1/2” Pulley Wrap the Press Cable 72 around a 3 1/2” Pulley Seat Assembly Leg Press Plate 16 must be on the upper edge Do not tighten the 5/16” Nylon Locknuts CHANGING THE WEIGHT SETTING WEIGHT RESISTANCE CHART TIGHTENING THE CABLES TROUBLESHOOTING AND MAINTENANCEPage 73, 52” CABLE DIAGRAMSCABLE ID CHART Press CableButterfly Cable Low CableRear Cable Ab Cable1-800-FON-PART FULL 90 DAY WARRANTYREPLACEMENT PARTS QUESTIONS?Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled 1 Cover Cap 1 3/4 Square Inner Cap 2 Square Inner Cap 3/4 Round Inner Cap Round Inner Cap 1” Retainer1 Square Inner Cap 1 Round Inner CapPART IDENTIFICATION CHART-Model No. 831.159830 R0402A 3/8 x 3 3/4 Bolt 3/8 x 4 Bolt 3/8 x 4 Carriage Bolt 3/8 x 4 1/4 Bolt 5/16 x 1 3/4 Bolt 5/16 x 1 Shoulder Bolt 1” Tap Screw 1/4 x 3/4 Bolt5/16 x 3 Bolt 5/16 x 2 3/4 Shoulder Bolt 3/8 x 3 Bolt 3/8 x 3 1/4 Bolt 3/8 x 3 1/2 Bolt 3/8 x 3 1/2 Carriage BoltSAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUALDescription PART LIST-Model NoDescription EXPLODED DRAWING-Model No