Installation Requirements, Location Requirements

Installation Requirements

LOCATION REQUIREMENTS

Consider all of the following when selecting an installa- tion location for the water softener.

=Do not locate the water softener where freezing temperatures occur. Do not attempt to treat water over 120ºF. Freezing temperatures or hot water damage voids the warranty.

=To condition all water in the home, install the water softener close to the water supply inlet, and upstream of all other plumbing connections, except outside water pipes. Outside faucets should remain on hard water to avoid wasting conditioned water and salt.

=A nearby drain is needed to carry away regenera- tion discharge (drain) water. Use a floor drain, laundry tub, sump, standpipe, or other options (check your local codes). See "Air Gap Requirements" and "Valve Drain Requirements" sections.

=The water softener works on 24 volt, 60 Hz electri- cal power only, supplied by a direct plug-in trans- former (included). Provide an electrical outlet within 10 feet, in accordance with NEC and local codes.

=Always install the water softener between the water inlet and water heater. Any other installed water conditioning equipment should be installed between the water inlet and water softener (See Figure 4 below).

=Avoid installing in direct sunlight. Excessive sun heat may cause distortion or other damage to non- metallic parts.

PLUMBING CODES

All plumbing must be completed in accordance with national, state and local plumbing codes.

In the state of Massachusetts: The Commonwealth of Massachusetts plumbing code 248-CMR shall be adhered to. A licensed plumber shall be used for this installation.

AIR GAP REQUIREMENTS

A drain is needed for regeneration water (See Figure 3). A floor drain, close to the water softener, is preferred. A laundry tub, standpipe, etc. are other drain options. Secure valve drain hose in place. Leave an air gap of 1-1/2” between the end of the hose and the drain. This gap is needed to prevent backflow of sewer water into the water softener. Do not put the end of the drain hose into the drain.

		Drain	Drain
	Drain	Hose	Hose
1-1/2”	Hose
1-1/2”
air gap
	1-1/2”
	air gap	1-1/2”
		air gap
FLOOR DRAIN	STANDPIPE	LAUNDRY TUB

FIG. 3

THE PROPER ORDER TO INSTALL WATER TREATMENT EQUIPMENT

Untreated Water to Cold Water Outside Faucets to House

City Water Supply

Hot Water	Optional	Pressure	OR
to House		Pressure
to House		Tank
	Sediment	Tank
	Filter

Water	Water	Well Water Supply
Heater	Softener	Well
		Well
		Pump

FIG. 4

WHES48 specifications

The Whirlpool WHES48 is an advanced water softener designed to provide exceptional water quality for both residential and commercial applications. This model stands out in the market due to its effective water treatment capabilities and user-friendly features.

One of the primary characteristics of the WHES48 is its high capacity, which can handle up to 48,000 grains, making it ideal for large families or homes with significant water usage. This capacity allows for efficient removal of hardness minerals such as calcium and magnesium, which can cause scale buildup in plumbing and appliances. By softening the water, the WHES48 helps to extend the lifespan of faucets, water heaters, and other fixtures, providing significant savings over time.

The WHES48 features a modern demand-initiated regeneration system that optimizes salt and water usage. This technology ensures that regeneration only occurs when necessary, reducing waste and conserving resources. The system monitors water consumption patterns, meaning it regenerates during off-peak hours, further enhancing efficiency.

Another significant advantage of the Whirlpool WHES48 is its user-friendly digital control panel. This intuitive interface allows users to easily program the system for their specific needs and provides a clear display of water usage data, remaining salt levels, and system status. Additionally, the softener is equipped with a bypass valve, allowing homeowners to direct hard water to their taps if ever needed.

Installation is a straightforward process, thanks to the compact design and included installation kit. The WHES48 can fit comfortably in most spaces, making it a versatile option for various home layouts.

The Whirlpool WHES48 also emphasizes low maintenance, with a self-cleaning feature that reduces the need for frequent servicing. It uses food-grade salt, making it safe for households with children and pets.

In summary, the Whirlpool WHES48 is a robust and efficient water softener offering advanced features like high capacity, demand-initiated regeneration, and user-friendly monitoring. Combined with its low maintenance requirements, this model serves as an excellent investment for anyone seeking to improve their home’s water quality and protect their plumbing systems.

Whirlpool WHES48 operation manual Installation Requirements, Location Requirements, Plumbing Codes

Models: WHES48