Iset | Xantrex Technology GPIB-XPD guide

Installation and Configuration

Remote/Local Operation

If the rear panel PON REM switch is set to 1, the power supply will power up in local mode. Power supply control is at the front panel. During an operating session, you can toggle between local mode and remote mode by sending commands as described in “Remote Mode Operation” on page 22 and “Local Mode Operation” on page 23.

Table 2.5 Remote Mode Power On Conditions

Condition	Default Settings	7.5-140 Model Example

Voltage	0 V	VSET 0

Current	0 A	ISET 0

Soft Voltage Limit	VMAX (see models)	VMAX 7.5

Soft Current Limit	IMAX (see models)	IMAX 140

OVP Trip Voltage	Model VMAX + 10%	OVSET 8.25

Delay	0.5 s	DLY 0.5S

Foldback Protection	OFF	FOLD OFF

Output	ON	OUT ON

Hold	OFF	HOLD OFF

Unmask	NONE	UNMASK NONE

Service Request Capability	OFF	SRQ OFF

AUXA	OFF	AUXA OFF

AUXB	OFF	AUXB OFF

Remote Mode While in remote mode, use the interface commands to control the output of the Operation power supply from a computer. See Section 3, “Operation” for a complete list of device-dependent commands available with this interface. For information about how to use GPIB commands and GPIB lines, refer to the documentation for the

particular GPIB controller interface installed on your computer.

While in remote mode, you can change to local mode operation by sending the

GPIB GTL (Go to Local) command, or by negating the GPIB REN (Remote

Enable) line.

22	Operating Manual for GPIB for XPD Series Power Supply

Image 24

Xantrex Technology GPIB-XPD manual Condition Default Settings Model Example, Iset

Contents

GPIB-XPD Page Internal Gpib Interface for XPD 500 Watt Series How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase Date Safety Supply Installation and Configuration Main SectionsManual Revisions About This Manual Contents Contents Features and Specifications Description Features and Functions Features and SpecificationsFunctions Readback Specifications Models 18-30 33-16 60-9 120-4.5OVP Features and Specifications Introduction Initial Inspection Power Supply Front Panel with Gpib Interface Installed Gpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB Basic Setup Procedure Step # Description Action ReferencePON SRQ IEEE-488 Primary Address Selection Address Power On Service Request PON SRQ Rear Panel SRQ Switch Position PON SRQ StateSwitch Position Power on results Condition Default Settings Model Example Iset IEEE-488 Controller Connection Internal PCB Jumper Selections OVP Control Mode Selection User Signals High OFF LOWHigh LOW OFF User Signals J21 Connector J21 User Signal Connector Circuit Block Diagram J21 User Cable with Ferrite Block Operation Gpib Operation Example Command directed to entire bus, or Bit Decimal Description Reset By Position Weight Request Service SRQ Set whenPower On PON Set when unit LSB Command Syntax Computer EntryFormat Description Form Floating Number Definition Example Iset 2.0A Vset Command Summary AUXA? AUXB?CMODE? DLY? FAULT? CmodeIdata IHI Command Reference Command DescriptionAuxa 1 on Auxb 1 on Changing an output setting Response Fold mode where mode is Snsp Mask None = Unmask ALL Status, and Fault Registers on Accumulated Status, Status, and Fault Registers on SNSP, ALL, None Response Vmax voltage Accumulated Status, Status, and Fault Registers Condition Mnemonic Bit Position Bit Weight Error Codes 11 Error Codes Troubleshooting LEDs Calibration Voltage Mode Calibration SetupVoltage Program Calibration Procedure Readback Voltage Calibration Current Mode Calibration Current Calibration SetupCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc