Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology GPIB-XPD manual Features and Functions, Readback

Models: GPIB-XPD

1 58

Download 58 pages 4.56 Kb

Page 14

Features and Specifications

Features and Functions

Features and Functions

Features • 16-bit programming and readback of voltage and current

•Programmable soft limits for voltage and current

•Programmable over voltage protection with reset

•Easy-to-use, self-documenting command set

•Isolated user-programmable signals such as fault, polarity, isolation, and auxiliary signals

•LED status signals: error, addressed, service request, over voltage protection, and remote operation

•Foldback in CV or CC mode with reset

•Local Lockout capability

•Software calibration

Programmable	•	Output voltage and current
Functions	•	Soft limits for voltage and current
	•	Overvoltage protection
	•	Output enable/disable
	•	Maskable fault interrupt
	•	Hold and trigger
	• User-programmable output relay signals
Readback	•	Actual measured voltage and current
Functions	•	Voltage and current settings
	• Soft voltage and current limits
	•	Overvoltage protection setting
	• Present and accumulated power supply status
	•	Programming error codes
	•	Fault codes
	• Power supply model and version identification
	•	Firmware revision levels

12	Operating Manual for GPIB for XPD Series Power Supply

Image 14

Xantrex Technology GPIB-XPD manual Features and Functions, Readback

Contents

Operating Manual Internal GPIB Interface for XPD Series Programmable DC Power SupplyGPIB-XPD Page Operating Manual for Internal GPIB Interface for XPD 500 Watt SeriesProgrammable DC Power Supply How do you get service? Limited WarrantyProof of purchase may be in any one of the following forms Disclaimer Product Information About Your Power Supply WARNING Limitations on UseWarnings Cautions and Notes PowerSafety SupplyDescribes the power supply and lists Main SectionsManual Revisions its features and specificationsOperating Manual for GPIB for XPD Series Power Supply About This ManualConfiguration Section Operation ContentsSection Features and Specifications Section Installation and Contents Section 1. Features and Specifications DescriptionReadback Features and FunctionsFunctions FunctionsModels SpecificationsFeatures and Specifications 7.5-67Operating Manual for GPIB for XPD Series Power Supply Features and SpecificationsSpecifications Initial Inspection Section 2. Installation and ConfigurationIntroduction Operating Manual for GPIB for XPD Series Power Supply Installation and ConfigurationFigure 2.1 Power Supply Front Panel with GPIB Interface Installed Initial InspectionInitial Inspection Installation and ConfigurationFigure 2.2 GPIB Interface Subplate Located on Power Supply Rear Panel Initial Inspection Installation and ConfigurationLED INDICATORS JUMPER SELECTIONBasic Setup Procedure IEEE-488 Primary Address Selection Power On Service Request PON SRQ Remote/Local Operationparticular GPIB controller interface installed on your computer Example IEEE-488 Controller ConnectionInternal PCB Jumper Selections Internal PCB Jumper Selections Table 2.6 OVP Control Mode SelectionUser Signals User SignalsFigure 2.4 User Signals J21 Connector To install the ferrite block To J21 Connector To User Custom Interface Installation and ConfigurationUser Signals Operating Manual for GPIB for XPD Series Power SupplyIntroduction Section 3. OperationGPIB Operation Example Then use ExampleRequest Service SRQ - Set when Reset ByWeight Power On PON - Set when unitMASK FOLD ≠ MK FOLD Command SyntaxMASK FOLD = mask fold MASK FOLD ≠ MASK FDDescription Command SyntaxOperation FormCOMMAND parameter COMMAND parameter, parameterLF ExampleDescription Command SummaryOperation Description Query CommandsOperation Description Calibration CommandsOperation DescriptionCommand Command Referenceread. See “Accumulated Status, Status, and Fault Registers” on page OperationOperation Commandbeen masked using the MASK command, then the ERR bit in the registers DescriptionDescription CommandOperation Operation Status, and Fault Registers” on page 46. Mnemonics are separated fromCommand DescriptionCommand switch on the supply. See “Power On Service Request PON SRQ” onStatus, and Fault Registers” on page OperationCommand “Accumulated Status, Status, and Fault Registers” on pagestatus and fault registers See “Accumulated Status, Status, and Fault Registers” on pageDescription CommandOperation Operation Accumulated Status, Status, and Fault RegistersBit Weight ExampleERROR # Error CodesTable 3.11 Error Codes ERROR IDENTIFICATIONTroubleshooting LEDsSection 4. Calibration IntroductionProcedure SetupVoltage Program Calibration Procedure Voltage Readback Calibration Voltage Mode CalibrationCalibration Voltage Mode CalibrationCurrent Mode Calibration Current Calibration SetupCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page 604 422 8595 Tel 604 421 3056 Fax Xantrex Technology Inc8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 800 667 8422 Toll Free North America prg.info@xantrex.com